[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
bug#5291: 23.1.91; "bzr status" FAILED
From: |
Dan Nicolaescu |
Subject: |
bug#5291: 23.1.91; "bzr status" FAILED |
Date: |
Sat, 2 Jan 2010 14:17:30 -0800 (PST) |
Eli Zaretskii <eliz@gnu.org> writes:
> > Date: Sat, 2 Jan 2010 12:47:00 -0800 (PST)
> > From: Dan Nicolaescu <dann@ics.uci.edu>
> > Cc: 5291@debbugs.gnu.org
> >
> > Eli Zaretskii <eliz@gnu.org> writes:
> >
> > > I have set up Emacs to be the EDITOR for bzr via emacsclient (yes, I'm
> > > invoking bzr from the command line). That works, but every time I
> > > commit a file to upstream, Emacs bitches with the following message in
> > > *Messages*:
> > >
> > > vc-do-command: Running bzr status bzr_log.uuzkwa...FAILED (status 3)
> >
> > Do you get a backtrace if you set debug-on-error?
>
> Yes, see below.
>
> AFAICT, it shouldn't even try to run "bzr status" on this file, since
> it's a temporary file used by bzr for the commit message. But if it
> somehow must run "bzr status", then it shouldn't signal an error when
> it predictably fails. But maybe I'm missing something.
>
> Debugger entered--Lisp error: (error "Running bzr status
bzr_log.ahvp69...FAILED (status 3)")
> signal(error ("Running bzr status bzr_log.ahvp69...FAILED (status 3)"))
> error("Running %s...FAILED (%s)" "bzr status bzr_log.ahvp69" "status 3")
> vc-do-command(t 0 "bzr" "d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69" "status")
> apply(vc-do-command t 0 "bzr" "d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69"
"status" nil)
> vc-bzr-command("status" t 0 "d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> vc-bzr-status("d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> vc-bzr-state("d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> vc-bzr-state-heuristic("d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> vc-bzr-registered("d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> apply(vc-bzr-registered "d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> vc-call-backend(Bzr registered "d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> #[(b) "\302\303 #\205\304 \305#\205\306\307\310\"\207" [b file
vc-call-backend registered vc-file-setprop vc-backend throw found t] 4](Bzr)
> mapc(#[(b) "\302\303 #\205\304 \305#\205\306\307\310\"\207"
[b file vc-call-backend registered vc-file-setprop vc-backend throw found t] 4]
(RCS CVS SVN SCCS Bzr Git Hg Mtn Arch))
> byte-code("\303\304\"\305\306 \203 \307=\203\n\202
\nB\"\210)\310\304\307#\210\311\207" [file backend vc-handled-backends
vc-file-getprop vc-backend mapc #[(b) "\302\303 #\205\304
\305#\205\306\307\310\"\207" [b file vc-call-backend registered
vc-file-setprop vc-backend throw found t] 4] none vc-file-setprop nil] 4)
> vc-registered("d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> vc-backend("d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69")
> vc-after-save()
> basic-save-buffer()
> save-buffer(1)
> call-interactively(save-buffer nil nil)
Strange.
What exactly creates the d:/gnu/bzr/emacs/trunk/bzr_log.ahvp69 file?
Is your TEMP set to d:/gnu/bzr/emacs/trunk/ ?
I think that if you change:
(vc-bzr-command "status" t 0 file)
to:
(vc-bzr-command "status" t 3 file)
in vc-bzr-status
it should work, but I am not 100% sure that's TRTD.
bug#5291: marked as done (23.1.91; "bzr status" FAILED), Emacs bug Tracking System, 2010/01/09