[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
BGPD died with "select error"
From: |
Thomas Trede |
Subject: |
BGPD died with "select error" |
Date: |
Mon, 13 May 2002 08:41:23 +0200 |
Hello,
I am using FreeBSD 4.5-Stable.
I got after approximately 48 hours the following bgpd.log output when
testing zebra:
2002/05/07 18:55:06 BGP: BGPd 0.92a starting: address@hidden, address@hidden
2002/05/07 19:05:23 BGP: 217.195.0.253 [Error] bgp_read_packet error:
Connection reset by peer
2002/05/07 19:07:31 BGP: 217.195.0.253 [Error] bgp_read_packet error:
Connection reset by peer
2002/05/09 18:50:54 BGP: select error: Invalid argument
Effect was, that the main interface was up, bgpd-process had died, all
bgp-routes were still in the kernel and in the zebra routing table.
I am using two remote routers to send full BGP routing table (approximately
108000 routes) to the FreeBSD box.
I have rebooted the box, and since approximately 3 days everything is
looking fine.
Is it a bug?
My configuration file is as follows:
bgpg.conf:
! -*- bgp -*-
!
! BGPd sample configuratin file
!
! $Id: bgpd.conf.sample,v 1.19 1999/02/19 17:17:27 developer Exp $
!
hostname test
password xxxx
enable password xxxxx
!
!bgp mulitple-instance
!
router bgp 65535
bgp router-id 212.223.91.101
! network 10.0.0.0/8
! neighbor 10.0.0.2 remote-as 7675
! neighbor 10.0.0.2 route-map set-nexthop out
! neighbor 10.0.0.2 ebgp-multihop
! neighbor 10.0.0.2 next-hop-self
neighbor 212.63.128.6 remote-as 8741
neighbor 212.63.128.6 ebgp-multihop 3
neighbor 212.63.128.6 distribute-list nix out
neighbor 212.63.128.6 route-map test in
neighbor 212.63.128.6 soft-reconfiguration inbound
neighbor 212.63.128.6 next-hop-self
!
neighbor 217.195.0.253 remote-as 20653
neighbor 217.195.0.253 ebgp-multihop 6
neighbor 217.195.0.253 distribute-list nix out
neighbor 217.195.0.253 route-map test in
neighbor 217.195.0.253 soft-reconfiguration inbound
neighbor 217.195.0.253 next-hop-self
!
! access-list all permit any
access-list nix deny any
!
route-map test permit 10
set ip next-hop 212.223.91.97
!
!route-map set-nexthop permit 10
! match ip address all
! set ip next-hop 10.0.0.1
!
log file bgpd.log
!
!log stdout
zebra.conf:
! -*- zebra -*-
!
! zebra sample configuration file
!
! $Id: zebra.conf.sample,v 1.14 1999/02/19 17:26:38 developer Exp $
!
hostname test
password xxxx
enable password xxxxx
!
! Interface's description.
!
!interface lo
! description test of desc.
!
!interface sit0
! multicast
!
! Static default route sample.
!
!ip route 0.0.0.0/0 203.181.89.241
!
log file zebra.log
ifconfig -a:
fxp0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
inet 212.223.91.101 netmask 0xffffffe0 broadcast 212.223.91.127
ether 00:02:b3:1a:8e:85
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
Kind regards,
Thomas Trede
- BGPD died with "select error",
Thomas Trede <=