sumitstop wrote:
>
> go to the directory /usr/local/bin
> there u will find benchmark files for ofdm (both transmission and
> reception)
> u need to type benchmark_ofdm_rx.py -h
> and benchmark_ofdm_tx.py -h
>
> these will show you the parameters u can play with.
>
> after that u can run these files by typing ./benchmark_ofdm_tx.py -f
> <frequency appropriate to ur daughter board>
> and ./benchmark_ofdm_rx.py -f <frequency appropriate to ur daughter board>
>
> also there may be drift in the center frequency of the daughter board so u
> can do one thing. first run the transmitter part and see on the spectrum
> analyzer for the center frequency of the ofdm signal.
>
> after that run the receiver part with that center frequency specified in
> the arguments.
> now run the transmitter again with the same frequency.
>
> if u get timeouts then u need to play with the receiver gain and
> transmitter amplitude as well as the receiver center frequency.
>
> u can change the bandwidth of the ofdm signal by changing the no of
> occupied tones or fft length because bw = occupied tones/ fft length
>
> let me know ur results.
>
> Regards
>
> waqasme wrote:
>>
>> hello sumit,
>> yah i have replaced the GMSK modulator and demodulator with OFDM
>> modulator and demaodulator. but i coudlnot find message source , ,message
>> sink, probe signal and probe avg mag 2 with only input .. the one i have
>> found has input and output as well for probe avg mag 2 block... i
>> couldnot able to find these blocks as in the simple tranceiver diagram
>> example they used these blocks... can you plesase guide me where to get
>> these blocks?
>> Also you mentioned this command ( benchmark_ofdm.py -h ) is that a
>> command or what? because i have entered this command in terminal window
>> but it says command not found? and if i type in google to search it opens
>> a c ++ code ..what i am suppose to do with that. ?? please tell me how to
>> use this benchmark_ofdm.py code.. where to put this code to make the
>> simulation work. i am very new to GNU radio so i have no idea what
>> functions i can play with and how to implement this. please guide me
>> like how to make this OFDM tranmission and reception via USRP. iam
>> using Linux Ubuntu maveric and GNU Radio companion 3.2.2 version... I
>> really appriciate your help because i have only few time left for my
>> Masters project. Thanks in advance i am looking forward to hear from you.
>>
>> Regards,
>> Waq.
>>
>> sumitstop wrote:
>>>
>>>
http://pwnhome.files.wordpress.com/2011/04/simple_transceiver1.png
>>> see carefully....... it has a gmsk modulator in the bottom.u can make
>>> the bottom modulator part in another pc
>>>
>>> benchmark programs are quite good to start with...
>>> u can type benchmark_ofdm.py -h to see all the parameters u can play
>>> with.
>>>
>>>
>>> waqasme wrote:
>>>>
>>>> And sorry to mention in the last mail that i will be suing USRP 1 .
>>>>
>>>> waqasme wrote:
>>>>>
>>>>> Hi Sumit,
>>>>> Thank you so much for your quick response. yah i understand what your
>>>>> saying and i am trying to understand this document but it doesnot help
>>>>> much . As you mentioned use the same Tranceiver setup and only replace
>>>>> OFDM blocks with that. My question is in this basic tranciver diagram
>>>>> the used two UHD's source and sink and in the middle they use GMSK
>>>>> Demodulator right. but they didnot use any modulator any where in the
>>>>> design. Now i am confused what blocks i have to replace with OFDM
>>>>> blocks??? Please try to explain in bit detail so i can design it
>>>>> properly .
>>>>> OR you mentioned other option that use benchmark_OFDM.py file .
>>>>> Somebody already told me about this benchmark file. but its just C++
>>>>> code . i am quite new to GNU radio and dont know much about the
>>>>> functions how it works.
>>>>> Please let me know how to use that benchmark_OFDM.py file in order to
>>>>> make the simulation design? do i have to download the file or what?
>>>>> how it works ?? let me know if you know about the process how to
>>>>> compile and run that code in GNU radio.
>>>>>
>>>>> Thanks for ur help and support really appriciate that...
>>>>>
>>>>> Regards,
>>>>>
>>>>> Waqas.
>>>>>
>>>>>
>>>>> sumitstop wrote:
>>>>>>
>>>>>> Try to understand these
>>>>>>
>>>>>>
http://pwnhome.wordpress.com/2011/04/26/intro-to-gnuradio-and-the-usrp-part-5-simple-transceiver/
>>>>>>
>>>>>> here u need to put those ofdm blocks .. thats it.... also go through
>>>>>> some modifications as written in umit,
>>>>>>
>>>>>>
>>>>>>
http://pwnhome.wordpress.com/2011/04/19/intro-to-gnuradio-and-the-usrp-part-4/
>>>>>>
>>>>>> or else work with benchmark_ofdm.py its very easy.. :)
>>>>>>
>>>>>> may i know what daughter boards do you have...
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> waqasme wrote:
>>>>>>>
>>>>>>>
>>>>>>> Hello sumit,
>>>>>>> Thanks for your help i went through that document that you refered
>>>>>>> to, and i tried to implement that OFDM transmitter part. This
>>>>>>> document only explain about OFDM flow graph or transmitter. Is there
>>>>>>> any other document or information related to OFDM modulator and
>>>>>>> demodulator (Transceiver)? i haver to implement OFDM transmission
>>>>>>> and reception via USRP. i will really appriciate if you can help me
>>>>>>> that or someone else who knows how to implement by using GNU radio
>>>>>>> companion.
>>>>>>> Thanks in advance.
>>>>>>> Regards,
>>>>>>> Waq.
>>>>>>>
>>>>>>>
>>>>>>
>>>>>>
>>>>>
>>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>
--