There was an ABI change between Gnu Radio and UHD, so you have to
be running a newer UHD--current master is what I'd recommend.
Also,
you'll find your world is better if you use build-gnuradio, if you're on
Ubuntu or Fedora.
On Thu, 2 Feb 2012 21:41:50 +0100 (CET),
address@hidden wrote:
Hello,
I would like to ask
for an advice - I have troubles running current
gnuradio git version
with USRP1 using UHD.
I have installed UHD drivers with downloaded
firmware and FPGA images and compiled the host code; uhd_usrp_probe
seems to work:
linux; GNU C++ version 4.5.3; Boost_104700;
UHD_003.003.002-unknown
-- Loading firmware image:
/usr/local/share/uhd/images/
usrp1_fw.ihx... done
-- Opening a USRP1
device...
-- Loading FPGA image:
/usr/local/share/uhd/images/
usrp1_fpga.rbf... done
-- Using FPGA clock
rate of 64.000000MHz...
______________________________
_______________________
/
| Device:
USRP1 Device
| _____________________________________________________
| /
| | Mboard: USRP1 (Classic)
| | serial: 46390f8b
| |
| |
Time sources: none
| | Clock sources: internal
| | Sensors:
| |
______________________________
_______________________
| | /
| | | RX
DSP: 0
| | | Freq range: -32.000 to 32.000 Mhz
| |
______________________________
_______________________
| | /
| | | RX
DSP: 1
| | | Freq range: -32.000 to 32.000 Mhz
| |
______________________________
_______________________
| | /
| | | RX
Dboard: A
| | | ID: WBX, WBX + Simple GDB (0x0053)
| | |
______________________________
_______________________
| | | /
| | |
| RX Subdev: 0
| | | | Name: WBX RX + Simple GDB
| | | | Antennas:
TX/RX, RX2
| | | | Sensors: lo_locked
| | | | Freq range: 68.750 to
2200.000 Mhz
| | | | Gain range PGA0: 0.0 to 31.5 step 0.5 dB
| | |
| Connection Type: IQ
| | | | Uses LO offset: No
| | |
______________________________
_______________________
| | | /
| | |
| RX Codec: A
| | | | Name: ad9522
| | | | Gain range pga: 0.0 to
20.0 step 1.0 dB
| |
______________________________
_______________________
| | /
| | | RX
Dboard: B
| | | ID: DBSRX (0x0002)
| | |
______________________________
_______________________
| | | /
| | |
| RX Subdev: 0
| | | | Name: DBSRX (0x0002)
| | | | Antennas: J3
|
| | | Sensors: lo_locked
| | | | Freq range: 800.000 to 2400.000 Mhz
| | | | Gain range GC1: 0.0 to 56.0 step 0.5 dB
etc..
Then I
installed gnuradio from git clone and configured it as:
./configure
--enable-gr-uhd --enable-gr-noaa --enable-usrp2 --enable-usrp
--enable-gr-usrp --enable-grc --enable-gr-audio-alsa --enable-gr-trellis
--disable-volk
I had to disable volk due to compilation errors (some
32-64 bit code mismatch I guess).
It seems that old USRP (non-UHD)
support has been already removed and when I trysome UHD example, it
always coredumps:
AFTER USRP POWER CYCLE
address@hidden:/scratch/jiri/
gnuradio/gr-uhd/examples/ ./usrp_wfm_rcv_pll.py
linux; GNU C++ version 4.5.3; Boost_104700; UHD_003.003.002-unknown
-- Loading firmware image: /usr/local/share/uhd/images/
usrp1_fw.ihx...
done
-- Opening a USRP1 device...
-- Loading FPGA image:
/usr/local/share/uhd/images/
usrp1_fpga.rbf... done
(gdb) bt
#0
0x00000000034b0018 in ?? ()
#1 0x00007fbb65892cb2 in thread_proxy ()
from /usr/lib64/libboost_thread-mt-
1_42.so.1.42.0
#2
0x00007fbb671c5ca8 in start_thread () from /lib64/libpthread.so.0
#3
0x00007fbb66f0c1ad in clone () from /lib64/libc.so.6
WITHOUT POWER
CYCLE
-- Opening a USRP1 device...
-- Using FPGA clock rate of
64.000000MHz...
Segmentation fault (core dumped)
#0
0x00007ffb61a855a4 in boost::thread::start_thread() () from
/usr/lib64/libboost_thread-mt-
1_42.so.1.42.0
(gdb) bt
#0
0x00007ffb61a855a4 in boost::thread::start_thread() () from
/usr/lib64/libboost_thread-mt-
1_42.so.1.42.0
#1 0x00007ffb5839d71b in
boost::thread* boost::thread_group::create_
thread const&>,
boost::_bi::list2, boost::_bi::value > > > >(boost::_bi::bind_t const&>,
boost::_bi::list2, boost::_bi::value > > >) () from
/usr/local/lib64/libuhd.so.003
#2 0x00007ffb5839e5ca in
task_impl::task_impl(boost::
function const&) () from
/usr/local/lib64/libuhd.so.003
#3 0x00007ffb5839bd71 in
uhd::task::make(boost::
function const&) () from
/usr/local/lib64/libuhd.so.003
#4 0x00007ffb582d40c6 in
usrp1_impl::io_init() () from /usr/local/lib64/libuhd.so.003
#5
0x00007ffb582f440c in usrp1_impl::usrp1_impl(uhd::
device_addr_t const&)
() from /usr/local/lib64/libuhd.so.003
#6 0x00007ffb582f5871 in
usrp1_make(uhd::device_addr_t const&) () from
/usr/local/lib64/libuhd.so.003
#7 0x00007ffb582f952c in
boost::detail::function::
function_invoker1 (*)(uhd::device_addr_t
const&), boost::shared_ptr, uhd::device_addr_t
const&>::invoke(boost::detail:
:function::function_buffer&,
uhd::device_addr_t const&) () from /usr/local/lib64/libuhd.so.003
#8
0x00007ffb583a34c3 in uhd::device::make(uhd::device_
addr_t const&,
unsigned long) () from /usr/local/lib64/libuhd.so.003
#9
0x00007ffb581e9b49 in uhd::usrp::multi_usrp::make(
uhd::device_addr_t
const&) () from /usr/local/lib64/libuhd.so.003
#10 0x00007ffb5868c3bb
in uhd_usrp_source_impl::uhd_
usrp_source_impl (this=0x2f90950,
device_addr=..., stream_args=...,
__in_chrg=, __vtt_parm=) at
gr_uhd_usrp_source.cc:68
#11 0x00007ffb5868322c in
uhd_make_usrp_source (device_addr=..., stream_args=...) at
gr_uhd_usrp_source.cc:473
#12 0x00007ffb588f572e in
_wrap_usrp_source__SWIG_1 (args=) at python/uhd_swig.cc:30153
#13
_wrap_usrp_source (self=, args=) at python/uhd_swig.cc:30188
#14
0x00007ffb636b1062 in PyEval_EvalFrameEx () from
/usr/lib64/libpython2.7.so.1.0
#15 0x00007ffb636b2f27 in
PyEval_EvalCodeEx () from /usr/lib64/libpython2.7.so.1.0
.....
On
the other hand, I have also funcube-dongle, and the same version of
gnuradio
works fine with that device.
I have python 2.7, boost
1.42.0 (with both 1.46 and 1.47 I got compilation errors in gnuradio),
gcc (Gentoo 4.5.3-r1 p1.0, pie-0.4.5) 4.5.3,
running 3.1.5-gentoo #2
SMP on x86_64 Intel(R) Core(TM) i7 CPU Q 740 @ 1.73GHz
HP 8540w
laptop.
I tried also to install gnuradio-3.4.2: this has still the
old USRP support, which works fine, but UHD segfaults as well (and
funcube does not work).
Do you have any idea what to do?
Thanks
very much for help.
Best regards,
Jiri Pittner
______________________________
_________________
Discuss-gnuradio
mailing list