Re: [Discuss-gnuradio] U's and L's when running GNU Radio

[khalid.el-darymli]

Hi Marcus, Hi Sylvain,

Thank you for your response. I continue to get these ULLLLLLLLLLLLLLLL even on a PC with really high specs.

Please find below my answers to your questions.

>> Do you use timed_commands? 

Yes, I do. In the python script, I simply use get_time_now() to query the times of both the Sink and the Source. Then, I convert this to a format understandable to python and I keep hold of the greater time of the two, I call it start_delay. Then, using set_start_time(), I make sure that both the Sink and the Source start at time start_delay.

Is there any problem with my timed_commands?

>> What are your RX and TX sampling rates? 

It's 100e06/256 = 390,625 Hz for both Tx and Rx.

>> From your network throughput, I'd assume your using 4x 3.3MS/s, is that correct?

I am using four Rx channels, and just one Tx channel. Based on the NW history in the link below,

https://lists.gnu.org/archive/html/discuss-gnuradio/2015-01/png5hOoJln6ra.png

My throughput is around 1.6 MB/s for each channel. This is set automatically by GNU Radio. Do I need to adjust it?

Thank you.

Best regards,

Khalid

Re: U's and L's when running GNU Radio

Marcus Müller (Guest)

on 2015-01-07 15:24

Hello Sylvain, hello Khalid,

these could be underruns (U) and late (L) packets, as reported by UHD,
used via gr-uhd; however, seeing so many L's is a very uncommon pattern;
Do you use timed_commands? What are your RX and TX sampling rates? From
your network throughput, I'd assume your using 4x 3.3MS/s, is that
correct?

Could you share the whole output of your program's run, not only the
ULLLL... ?

Best regards,
Marcus

Re: U's and L's when running GNU Radio

Sylvain Munaut (Guest)

on 2015-01-07 14:48

Hi,

> In the terminal and while using a powerful PC (please see the attachment), I
> am occasionally getting capital U's and L's when running GNU Radio with one
> Tx and 4 Rx channels (Here is a sample of what I am getting:
> ULLLLLLLLLLLLLLLULLLLULLLLLLLLLLLLLLLULLLULLLLLLLLLLLLLLLLLLLLLLLLLLLL).

I can't find anything in GNURadio itself that would print that.

The only thing it can print AFAICT is aU aO jU

So it must be an OOT block that display those ...

Cheers,

   Sylvain

U's and L's when running GNU Radio

Khalid Eldarymli (khalide)

on 2015-01-05 17:50

Attachment: SystemMonitor.png (100 KB)

Hi,

In the terminal and while using a powerful PC (please see the
attachment),
I am occasionally getting capital U's and L's when running GNU Radio
with
one Tx and 4 Rx channels (Here is a sample of what I am getting:
ULLLLLLLLLLLLLLLULLLLULLLLLLLLLLLLLLLULLLULLLLLLLLLLLLLLLLLLLLLLLLLLLL).

Please note that I am using timed-commands to start both the Tx and Rx's
at
the same time. When I check the System Monitor while GNU Radio is
running
(please see the attachment), the CPU history and RAM usage seem to be
fine.
Also, swap memory is disabled as shown in the attachment. What causes
this
issue and how to handle it? Could it be due to some instability in the
writing speed to the hard drive?

BTW, I am having the same issue for my older PC (a PC with less specs).
The
System Monitor tells me that my CPU usage is around 60% and my RAM usage
is
around 45%, however, I am getting U's and L's when I try to use four Rx
channels. Please note that the system doesn't throw lots of U's and L's
at
once, it is a kind of frequent where a bunch of them are thrown out
every
many seconds or so.

Thanks in advance for your help.

Best regards,
Khalid