[Emacs-diffs] /srv/bzr/emacs/trunk r109382: calc.texi (Simplification modes, Conversions)

[Jay Belanger]

------------------------------------------------------------
revno: 109382
committer: Jay Belanger <address@hidden>
branch nick: trunk
timestamp: Wed 2012-08-01 18:42:29 -0500
message:
  calc.texi (Simplification modes, Conversions)
  (Operating on Selections, Basic Simplifications)
  (Algebraic Simplifications):  Mention "basic" simplifications.
  (Algebraic Entry): Remove mention of default simplifications.
modified:
  doc/misc/ChangeLog
  doc/misc/calc.texi

=== modified file 'doc/misc/ChangeLog'
--- a/doc/misc/ChangeLog        2012-08-01 18:24:13 +0000
+++ b/doc/misc/ChangeLog        2012-08-01 23:42:29 +0000
@@ -1,6 +1,7 @@
 2012-08-01  Jay Belanger  <address@hidden>
 
-       * calc.texi (Simplification modes): Mention "basic" simplification.
+       * calc.texi (Simplification modes, Conversions)
+       (Operating on Selections): Mention "basic" simplification.
        (The Calc Mode Line): Mention the mode line display for Basic
        simplification mode.
        (Simplify Formulas): Refer to 'algebraic' rather than 'default'
@@ -14,6 +15,7 @@
        (Trigonometric/Hyperbolic Functions, Reducing and Mapping)
        (Kinds of Declarations, Functions for Declarations):  Mention
        "algebraic simplifications" instead of `a s'.
+       (Algebraic Entry): Remove mention of default simplifications.
 
 2012-07-30  Jay Belanger  <address@hidden>
 

=== modified file 'doc/misc/calc.texi'
--- a/doc/misc/calc.texi        2012-08-01 18:24:13 +0000
+++ b/doc/misc/calc.texi        2012-08-01 23:42:29 +0000
@@ -10123,7 +10123,7 @@
 the variable @samp{pi}, but @kbd{' pi address@hidden pushes 3.1415.)
 
 If you finish your algebraic entry by pressing @key{LFD} (or @kbd{C-j})
-instead of @key{RET}, Calc disables the default simplifications
+instead of @key{RET}, Calc disables simplification
 (as if by @kbd{m O}; @pxref{Simplification Modes}) while the entry
 is being pushed on the stack.  Thus @kbd{' 1+2 @key{RET}} pushes 3
 on the stack, but @kbd{' 1+2 @key{LFD}} pushes the formula @expr{1+2};
@@ -12613,12 +12613,12 @@
 
 @kindex m B
 @pindex calc-bin-simplify-mode
-The @kbd{m B} (@code{calc-bin-simplify-mode}) mode applies the limited
+The @kbd{m B} (@code{calc-bin-simplify-mode}) mode applies the basic
 simplifications to a result and then, if the result is an integer,
 uses the @kbd{b c} (@code{calc-clip}) command to clip the integer according
 to the current binary word size.  @xref{Binary Functions}.  Real numbers
 are rounded to the nearest integer and then clipped; other kinds of
-results (after the default simplifications) are left alone.
+results (after the basic simplifications) are left alone.
 
 @kindex m A
 @pindex calc-alg-simplify-mode
@@ -16714,10 +16714,10 @@
 operation.  Vectors and formulas are cleaned by cleaning each component
 number (i.e., pervasively).
 
-If the simplification mode is set below the limited level, it is raised
-to the limited level for the purposes of this command.  Thus, @kbd{c c}
-applies the limited simplifications even if their automatic application
-is disabled.  @xref{Simplification Modes}.
+If the simplification mode is set below basic simplification, it is raised
+for the purposes of this command.  Thus, @kbd{c c} applies the basic
+simplifications even if their automatic application is disabled.
address@hidden Modes}. 
 
 @cindex Roundoff errors, correcting
 A numeric prefix argument to @kbd{c c} sets the floating-point precision
@@ -22124,7 +22124,7 @@
 @kindex j v
 @pindex calc-sel-evaluate
 The @kbd{j v} (@code{calc-sel-evaluate}) command performs the
-limited simplifications on the selected sub-formula.
+basic simplifications on the selected sub-formula.
 These simplifications would normally be done automatically
 on all results, but may have been partially inhibited by
 previous selection-related operations, or turned off altogether
@@ -22412,14 +22412,14 @@
 
 As well as the simplifications described here, if you have stored
 any rewrite rules in the variable @code{EvalRules} then these rules
-will also be applied before any built-in default simplifications.
+will also be applied before any of the basic simplifications.
 @xref{Automatic Rewrites}, for details.
 
 @tex
 \bigskip
 @end tex
 
-And now, on with the limited set of simplifications:
+And now, on with the basic simplifications:
 
 Arithmetic operators like @kbd{+} and @kbd{*} always take two
 arguments in Calc's internal form.  Sums and products of three or
@@ -22737,7 +22737,7 @@
 
 Products are sorted into a canonical order using the commutative
 law.  For example, @expr{b c a} is commuted to @expr{a b c}.
-This allows easier comparison of products; for example, the limited
+This allows easier comparison of products; for example, the basic
 simplifications will not change @expr{x y + y x} to @expr{2 x y},
 but the algebraic simplifications; it first rewrites the sum to
 @expr{x y + x y} which can then be recognized as a sum of identical
@@ -22796,10 +22796,10 @@
 Integer powers of the variable @code{i} are simplified according
 to the identity @expr{i^2 = -1}.  If you store a new value other
 than the complex number @expr{(0,1)} in @code{i}, this simplification
-will no longer occur.  This is not done by the limited
+will no longer occur.  This is not done by the basic
 simplifications; in case someone (unwisely) wants to use the name
 @code{i} for a variable unrelated to complex numbers, they can use
-limited simplifications.
+basic simplification mode.
 
 Square roots of integer or rational arguments are simplified in
 several ways.  (Note that these will be left unevaluated only in