[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Help-gnu-radius] Help: rancid+radius+cisco getting error
From: |
zulfadli |
Subject: |
[Help-gnu-radius] Help: rancid+radius+cisco getting error |
Date: |
Thu, 12 May 2011 16:29:29 +0800 |
Hi all,
I'm using rancid-2.3.3 and freeradius-1.1.3-1.6.el5. Both installed at
different machines. My problem is whenever I test rancid it gave error
below..
address@hidden bin]$ clogin clientA
ClientA
spawn telnet clientA
Trying x.x.x.34...
telnet: connect to address x.x.x.34: Connection refused
telnet: Unable to connect to remote host: Connection refused
spawn ssh -c 3des -x -l rancid clientA
rancid@ clientA 's password:
Permission denied, please try again.
Error: Check your passwd for clientA
I've checked in my radius that the password is correct.in fact if I try ssh
to clientA from my rancid machine everything is ok..
address@hidden bin]$ ssh rancid@ clientA
rancid@ clientA 's password:
clientA -PE01>
Here are some rancid files for your reference.
Router.db
clientA:cisco:up
clientB:cisco:up
.cloginrc
# clientA
# these routers ask for a username and password. we automatically get
# enable access after successful authentication.
add user clientA rancid
add password clientA mypassword
#add autoenable clientA 1
# clientB
# these routers ask for a username and password. we automatically get
# enable access after successful authentication.
add user clientB rancid
add password clientB mypassword
#add autoenable clientB 1
Log
Trying to get all of the configs.
clientA clogin error: Error: Check your passwd for clientA
clientA: missed cmd(s): admin show diag,dir /all slavedisk2:,show rsp
chassis-info,dir /all sec-slot2:,show diag,dir /all disk1:,show gsr
chassis,dir /all sec-nvram:,show diag chassis-info,dir /all disk2:,dir /all
sec-bootflash:,show spe version,dir /all slaveslot2:,dir /all disk0:,show
install active,show bootvar,dir /all slaveslot0:,dir /all sec-slot1:,dir
/all harddiska:,dir /all slavenvram:,show flash,dir /all sec-disk2:,dir /all
slavesup-bootflash:,dir /all sec-disk0:,dir /all harddiskb:,show variables
boot,show boot,show inventory raw,dir /all slavedisk1:,show env all,show
module,admin show env all,show controllers,admin show version,show
diagbus,more system:running-config,dir /all slavedisk0:,show debug,show
idprom backplane,dir /all bootflash:,dir /all sec-slot0:,dir /all
sec-disk1:,write term,show vtp status,dir /all sup-bootflash:,dir /all
slot2:,dir /all harddisk:,dir /all slot0:,dir /all sup-microcode:,show
vlan,dir /all slavebootflash:,show controllers cbus,dir /all slaveslot1:,dir
/all nvram:,show version,show vlan-switch,admin show variables boot,show
redundancy secondary,show running-config,show c7200,dir /all slot1:
clientA: End of run not found
Some radius file for your checking..
rancid Auth-Type := System
Service-Type = NAS-Prompt-User,
cisco-avpair = "shell:priv-lvl=15"
client x.x.x.x {
secret = secret_pass
shortname = clientA-PE01
nastype = cisco
What could possibly cause the problem here?can anyone help me on this?
Thank you and with regards
Zulfadli Syazwan Bin Razali
MYREN Application Engineer
Malaysian Research & Education Network (MYREN)
HP : 013 - 921 1482
Fax : 03 - 8318 5034
Ym! : address@hidden
Skype: zulfadlisyazwan
http://www.myren.net.my
[Prev in Thread] |
Current Thread |
[Next in Thread] |
- [Help-gnu-radius] Help: rancid+radius+cisco getting error,
zulfadli <=