|
From: | Kevin Wells |
Subject: | [Ltib] Additions to pkg.map |
Date: | Fri, 15 May 2009 22:18:53 +0200 |
We are adding support for the Apex bootloader on several products
under LTIB. Since this is in the common area, it might be a good idea
for someone else to quickly review it and make any comments. Thanks! ****************************** Changes to ./config/userspace/pkg.map below… ****************************** PKG_LM_SENSORS
= lm_sensors PKG_SDL
= sdl +PKG_APEX
= apex ****************************** New common spec file in new ./dist/lfs-5.1/apex directory… ****************************** %Build PKG_APEX_PRECONFIG=$(eval echo $PKG_APEX_PRECONFIG) : ${PKG_APEX_PRECONFIG:?must be set to the name of
your .config file} SRC_DIR=%{_builddir}/%{buildsubdir} %{!?showsrcpath: %define showsrcpath 0} %if %{showsrcpath} %{echo:%(eval echo %{_builddir})} %endif BUILD_DIR=%{_builddir}/%{buildsubdir} if [ $SRC_DIR != $BUILD_DIR ] then mkdir -p $BUILD_DIR fi cd $SRC_DIR export HOSTCC="$BUILDCC" export CROSS_COMPILE=$TOOLCHAIN_PREFIX export ARCH=arm if [ -n "$LTIB_FULL_REBUILD" ] then make distclean fi # Create a local copy of the config and use it
instead PKG_APEX_PRECONFIG_DEV=${PKG_APEX_PRECONFIG}.dev if [ -f
"$PLATFORM_PATH/$PKG_APEX_PRECONFIG_DEV" ] then # Copy file if it exists to Apex
directory cp
$PLATFORM_PATH/$PKG_APEX_PRECONFIG_DEV .config else if [ -f
"$PLATFORM_PATH/${PKG_APEX_PRECONFIG}" ] then # Create
temporary copy and copy it to Apex directory cp
$PLATFORM_PATH/${PKG_APEX_PRECONFIG} $PLATFORM_PATH/$PKG_APEX_PRECONFIG_DEV cp
$PLATFORM_PATH/$PKG_APEX_PRECONFIG_DEV .config else # An
important configuration file was missing, # We will
force build a local copy
PKG_APEX_WANT_CF=$(eval echo y) fi fi # Need an Apex configuration menu? if [ -n "${PKG_APEX_WANT_CF}" ] then make menuconfig fi # Save configuration changes cp .config $PLATFORM_PATH/$PKG_APEX_PRECONFIG_DEV # Build apex make apex.bin %Install rm -rf $RPM_BUILD_ROOT mkdir -p $RPM_BUILD_ROOT/%{pfx}/boot BUILD_DIR=%{_builddir}/%{buildsubdir} cd $BUILD_DIR for i in apex.bin do cp $i $RPM_BUILD_ROOT/%{pfx}/boot done %Clean if [ -n "$PKG_APEX_LEAVESRC" ] then rm -rf $RPM_BUILD_ROOT fi %Files %defattr(-,root,root) %{pfx}/* ****************************** One of a few new platform specific spec files in new ./dist/lfs-5.1/apex
directory… ****************************** # Template = apex-common.tmpl %define pfx /opt/nxp/rootfs/%{_target_cpu} Summary
: Apex bootloader Name
: apex Version
: 1.6.8 Release
: 1 License
: GPL Vendor
: NXP Packager :
Kevin Wells Group
: Applications/System Source
: %{name}-%{version}.tar.bz2 Patch0
: apex-1.6.8_mkfix.patch Patch1
: patch_apex-1.6.8_lpc313x BuildRoot :
%{_tmppath}/%{name} Prefix
: %{pfx} %Description %{summary} This specfile attempts to recreate the Apex 1.6.8
binary needed for the Embedded Artists 3131 board. %Prep %setup -n %{name}-%{version} %patch0 -p1 %patch1 -p1 ****************************** Make file patch ****************************** I'm not sure why, but the target compilers selected in LTIB
wouldn't be used unless I commented out the following lines in the main Apex makefile. That's the
apex-1.6.8-mkfix.patch patchfile. All it does is comment out the following lines. I couldn't figure out how
to get it to build without that fix so if anyone knows why and it's fixable, I can remove that patch. #HOSTCC = gcc #HOSTCXX = g++ #HOSTCFLAGS = -Wall -Wstrict-prototypes
-O2 -fomit-frame-pointer #HOSTCXXFLAGS
= -O2 thanks, Kevin Wells NXP Semiconductors |
[Prev in Thread] | Current Thread | [Next in Thread] |