ltib
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

RE: [Ltib] Toolchain error using ltib - M544X coldfire


From: Jon Burke
Subject: RE: [Ltib] Toolchain error using ltib - M544X coldfire
Date: Mon, 11 Jan 2010 09:44:38 -0000

Thanks for that Stuart, the install gets further now, but fails on
building the kernel. I haven't changed any of the LTIB or kernel
configuration settings from defaults. This is the error:

*** End of Linux kernel configuration.
*** Execute 'make' to build the kernel or try 'make help'.

+ '[' -f
/home/jon/ltib_latest/ltib/config/platform/mcf5445x/linux-2.6.x.config.d
ev ']'
+ diff -q ./.config
/home/jon/ltib_latest/ltib/config/platform/mcf5445x/linux-2.6.x.config.d
ev
+ '[' -n '' ']'
+ '[' '%{kernel_series}' = 2.4 ']'
+ make ARCH=m68k 'HOSTCC=ccache /usr/bin/gcc -B/usr/bin//' uImage
scripts/kconfig/conf -s arch/m68k/Kconfig
make: *** No rule to make target `uImage'.  Stop.
error: Bad exit status from /home/jon/ltib_latest/ltib/tmp/rpm-tmp.40015
(%build)


RPM build errors:
    Bad exit status from /home/jon/ltib_latest/ltib/tmp/rpm-tmp.40015
(%build)
Build time for kernel-2.6.20-m5445x: 35 seconds

Failed building kernel-2.6.20-m5445x

I presume your build was successful, is there something else I'm
missing?
Jon

-----Original Message-----
From: Stuart Hughes [mailto:address@hidden 
Sent: 08 January 2010 13:50
To: Jon Burke
Cc: address@hidden
Subject: Re: [Ltib] Toolchain error using ltib - M544X coldfire


Hi Jon,

It looks like the merge out from Freescale was inconsistent in some 
areas the m5445x platform was not in the toolchain config control files.

I've updated these now on Savannah to what I _think_ they should be.  If

you do a cvs update and re-run ./ltib -m config it should find them 
(remember to save).  I get this, please check yours is the same.  If it 
is, build and test.

--- Toolchain selection.
     Toolchain (gcc-4.3.43 eglibc-2.5.43 mk68k toolchain.)  --->
(-march=isac -mcpu=54455 -msoft-float) Enter any CFLAGS for gcc/g++

Regards, Stuart

Jon Burke wrote:
> Hello,
> I've previously successfully used LTIB for the coldfire M54455 using
the
> BSP on Freescale's website. But Freescale don't provide updates, and
it
> seems not to work on new Fedora 12. So I figured I would try the
version
> on Savannah. I followed the instructions in the FAQ, but when running
> ltib, I always get the following error:
> 
> You must set configuration values in config/platform/mcf5445x/.config
> for:
>   TOOLCHAIN_PREFIX TOOLCHAIN_PATH 
> traceback:
>  main::check_platform_config:2215
>   main::pre_build_checks:1455
>    main:558
> 
> I have "Freescale M544X coldfire/m68k (MMU)" selected as the target. I
> can see that it has installed various tools in /opt/ltib, but it does
> not seem to include gcc. The FAQ says toolchains "are stored on the
GPP
> as the binary rpms and will be downloaded and installed as required."
Is
> this wrong? Does anyone know if I need to install a toolchain myself
> first, and if so how?
> 
> Jon.
> 
> 
> _______________________________________________
> LTIB home page: http://ltib.org
> 
> Ltib mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/ltib
> 


This message has been scanned by MailController -
www.MailController.altohiway.com




reply via email to

[Prev in Thread] Current Thread [Next in Thread]