|
From: | Christophe De Wagter |
Subject: | Re: [Paparazzi-devel] www.jobyrobotics.com |
Date: | Tue, 13 Dec 2011 09:40:03 +0100 |
Hello Limaiem,
arduIMU V3 is based on a new chip, the MPU-6000. In my opinion there still is few documentation and few experience with it. I don't know if the are firmware issues (in MPU-6000, not arduIMU), calibration issues, etc.
As far as I know V3 is pin compatible with V2, but I do not know if they share the same logic interface.
Héctor--On Tue, Dec 13, 2011 at 12:18 AM, limaiem imed <address@hidden> wrote:
and what about the ArduIMU+ V3 ?
I think that in the paparazzi wiki there is a sample using the ArduIMU V2.
Specifications:
Digital-output of 6 or 9-axis MotionFusion data in rotation matrix,
quaternion, Euler Angle, or raw data format
Tri-Axis angular rate sensor (gyro) with a sensitivity up to 131
LSBs/dps and a full-scale range of ±250, ±500, ±1000, and ±2000dps
Tri-Axis accelerometer with a programmable full scale range of ±2g,
±4g, ±8g and ±16g
Reduced settling effects and sensor drift by elimination of
board-level cross-axis alignment errors between accelerometers and
gyroscopes
Digital Motion Processing™ (DMP™) engine offloads complex
MotionFusion, sensor timing synchronization and gesture detection
MotionApps™ Platform support for Android, Linux, and Windows, with
Windows Phone platforms on the roadmap
Digital-output temperature sensor
Digital input on FSYNC pin to support video Electronic Image
Stabilization and GPS
Programmable interrupt supports gesture recognition, panning, zooming,
scrolling, free fall interrupt, high-G interrupt, zero-motion
detection, tap detection, and shake detection
Full Chip Idle Mode Supply Current: 5µA
On-chip timing generator with ±1% frequency variation over full
temperature range
User self test
10,000g shock tolerant
Other ArduIMU V3 features:
Pin compatible with ArduIMU V2.
Breadboard compatible (ArduIMU V2 was not!).
Smaller size (1.5" x 1.0").
Atmega CPU has more % available for other tasks.
The 6 analog pins are now available!
Arduino compatible and open source.
3 status LED's (RGB).
I2C port with 3.3V translation.
GPS port with FTDI autoswitch.
This device is suitable for ANY application from rockets to simple
movement detection.
Imed LIMAIEM
address@hidden
On Tue, Dec 13, 2011 at 12:05 AM, Christophe De Wagter
<address@hidden> wrote:
>
> Sorry, forgot the link: http://www.ryanmechatronics.com/ProductDetailCHIMU.htm
>
> -Christophe
>
>
>
>
> On Tue, Dec 13, 2011 at 12:04 AM, Christophe De Wagter <address@hidden> wrote:
>>
>> For planes the ryan mechatronics CHIMU works right out of the box with paparazzi.
>>
>> If you have a spare serial port you can connect it via the easy usart interface, or if you don't have spare uarts or want even more performance there is a high speed SPI interface.
>>
>> The AHRS filter runs in the imu with GPS corrections sent to the device, and so far it was only tested on fixedwings.
>>
>> -Christophe
>>
>>
>>
>>
>> On Mon, Dec 12, 2011 at 10:25 PM, limaiem imed <address@hidden> wrote:
>>>
>>> In the paparazzi website there are a link to another provider:
>>> http://thequadshot.com/
>>> for Jobyrobotics, why don't you try to phone them ?
>>> Regards,
>>>
>>> Imed LIMAIEM
>>> address@hidden
>>>
>>>
>>>
>>> On Mon, Dec 12, 2011 at 10:09 PM, Cédric Marzer <address@hidden> wrote:
>>>>
>>>> Hello all,
>>>> I still don't have any news from Jobyrobotics. I ordered and paid for an aspirin IMU on the 16th of november and didn't get any feedback. The problem is definitly more serious than just a problem with the website. In my opinion the link on the paparazzi page should be removed asap.
>>>> Now the question remains : where could I get an IMU for my paparazzi plane ? If there is any other IMU that works out of the box with the paparazzi I would be interested.
>>>> Any help appreciated.
>>>> Cheers,
>>>> Cédric
>>>>
>>>>
>>>> _______________________________________________
>>>> Paparazzi-devel mailing list
>>>> address@hidden
>>>> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>>
>>>
>>>
>>> _______________________________________________
>>> Paparazzi-devel mailing list
>>> address@hidden
>>> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>>
>>
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
Héctor
_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
[Prev in Thread] | Current Thread | [Next in Thread] |