qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [4400] Add the LM8323-based keyboard of N810.


From: Andrzej Zaborowski
Subject: [Qemu-devel] [4400] Add the LM8323-based keyboard of N810.
Date: Fri, 09 May 2008 22:16:13 +0000

Revision: 4400
          http://svn.sv.gnu.org/viewvc/?view=rev&root=qemu&revision=4400
Author:   balrog
Date:     2008-05-09 22:16:11 +0000 (Fri, 09 May 2008)

Log Message:
-----------
Add the LM8323-based keyboard of N810.

Modified Paths:
--------------
    trunk/Makefile
    trunk/hw/i2c.h
    trunk/hw/nseries.c

Added Paths:
-----------
    trunk/hw/lm832x.c

Modified: trunk/Makefile
===================================================================
--- trunk/Makefile      2008-05-09 20:13:43 UTC (rev 4399)
+++ trunk/Makefile      2008-05-09 22:16:11 UTC (rev 4400)
@@ -52,7 +52,7 @@
 OBJS+=irq.o
 OBJS+=i2c.o smbus.o smbus_eeprom.o max7310.o max111x.o wm8750.o
 OBJS+=ssd0303.o ssd0323.o ads7846.o stellaris_input.o twl92230.o
-OBJS+=tmp105.o
+OBJS+=tmp105.o lm832x.o
 OBJS+=scsi-disk.o cdrom.o
 OBJS+=scsi-generic.o
 OBJS+=usb.o usb-hub.o usb-linux.o usb-hid.o usb-msd.o usb-wacom.o usb-serial.o

Modified: trunk/hw/i2c.h
===================================================================
--- trunk/hw/i2c.h      2008-05-09 20:13:43 UTC (rev 4399)
+++ trunk/hw/i2c.h      2008-05-09 22:16:11 UTC (rev 4400)
@@ -84,4 +84,8 @@
 void tmp105_reset(i2c_slave *i2c);
 void tmp105_set(i2c_slave *i2c, int temp);
 
+/* lm832x.c */
+struct i2c_slave *lm8323_init(i2c_bus *bus, qemu_irq nirq);
+void lm832x_key_event(struct i2c_slave *i2c, int key, int state);
+
 #endif

Added: trunk/hw/lm832x.c
===================================================================
--- trunk/hw/lm832x.c                           (rev 0)
+++ trunk/hw/lm832x.c   2008-05-09 22:16:11 UTC (rev 4400)
@@ -0,0 +1,535 @@
+/*
+ * National Semiconductor LM8322/8323 GPIO keyboard & PWM chips.
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Written by Andrzej Zaborowski <address@hidden>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 or
+ * (at your option) version 3 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include "hw.h"
+#include "i2c.h"
+#include "qemu-timer.h"
+#include "console.h"
+
+struct lm_kbd_s {
+    i2c_slave i2c;
+    int i2c_dir;
+    int i2c_cycle;
+    int reg;
+
+    qemu_irq nirq;
+    uint16_t model;
+
+    struct {
+        qemu_irq out[2];
+        int in[2][2];
+    } mux;
+
+    uint8_t config;
+    uint8_t status;
+    uint8_t acttime;
+    uint8_t error;
+    uint8_t clock;
+
+    struct {
+        uint16_t pull;
+        uint16_t mask;
+        uint16_t dir;
+        uint16_t level;
+        qemu_irq out[16];
+    } gpio;
+
+    struct {
+        uint8_t dbnctime;
+        uint8_t size;
+        int start;
+        int len;
+        uint8_t fifo[16];
+    } kbd;
+
+    struct {
+        uint16_t file[256];
+       uint8_t faddr;
+        uint8_t addr[3];
+        QEMUTimer *tm[3];
+    } pwm;
+};
+
+#define INT_KEYPAD             (1 << 0)
+#define INT_ERROR              (1 << 3)
+#define INT_NOINIT             (1 << 4)
+#define INT_PWMEND(n)          (1 << (5 + n))
+
+#define ERR_BADPAR             (1 << 0)
+#define ERR_CMDUNK             (1 << 1)
+#define ERR_KEYOVR             (1 << 2)
+#define ERR_FIFOOVR            (1 << 6)
+
+static void lm_kbd_irq_update(struct lm_kbd_s *s)
+{
+    qemu_set_irq(s->nirq, !s->status);
+}
+
+static void lm_kbd_gpio_update(struct lm_kbd_s *s)
+{
+}
+
+static void lm_kbd_reset(struct lm_kbd_s *s)
+{
+    s->config = 0x80;
+    s->status = INT_NOINIT;
+    s->acttime = 125;
+    s->kbd.dbnctime = 3;
+    s->kbd.size = 0x33;
+    s->clock = 0x08;
+
+    lm_kbd_irq_update(s);
+    lm_kbd_gpio_update(s);
+}
+
+static void lm_kbd_error(struct lm_kbd_s *s, int err)
+{
+    s->error |= err;
+    s->status |= INT_ERROR;
+    lm_kbd_irq_update(s);
+}
+
+static void lm_kbd_pwm_tick(struct lm_kbd_s *s, int line)
+{
+}
+
+static void lm_kbd_pwm_start(struct lm_kbd_s *s, int line)
+{
+    lm_kbd_pwm_tick(s, line);
+}
+
+static void lm_kbd_pwm0_tick(void *opaque)
+{
+    lm_kbd_pwm_tick(opaque, 0);
+}
+static void lm_kbd_pwm1_tick(void *opaque)
+{
+    lm_kbd_pwm_tick(opaque, 1);
+}
+static void lm_kbd_pwm2_tick(void *opaque)
+{
+    lm_kbd_pwm_tick(opaque, 2);
+}
+
+enum {
+    LM832x_CMD_READ_ID         = 0x80, /* Read chip ID. */
+    LM832x_CMD_WRITE_CFG       = 0x81, /* Set configuration item. */
+    LM832x_CMD_READ_INT                = 0x82, /* Get interrupt status. */
+    LM832x_CMD_RESET           = 0x83, /* Reset, same as external one */
+    LM823x_CMD_WRITE_PULL_DOWN = 0x84, /* Select GPIO pull-up/down. */
+    LM832x_CMD_WRITE_PORT_SEL  = 0x85, /* Select GPIO in/out. */
+    LM832x_CMD_WRITE_PORT_STATE        = 0x86, /* Set GPIO pull-up/down. */
+    LM832x_CMD_READ_PORT_SEL   = 0x87, /* Get GPIO in/out. */
+    LM832x_CMD_READ_PORT_STATE = 0x88, /* Get GPIO pull-up/down. */
+    LM832x_CMD_READ_FIFO       = 0x89, /* Read byte from FIFO. */
+    LM832x_CMD_RPT_READ_FIFO   = 0x8a, /* Read FIFO (no increment). */
+    LM832x_CMD_SET_ACTIVE      = 0x8b, /* Set active time. */
+    LM832x_CMD_READ_ERROR      = 0x8c, /* Get error status. */
+    LM832x_CMD_READ_ROTATOR    = 0x8e, /* Read rotator status. */
+    LM832x_CMD_SET_DEBOUNCE    = 0x8f, /* Set debouncing time. */
+    LM832x_CMD_SET_KEY_SIZE    = 0x90, /* Set keypad size. */
+    LM832x_CMD_READ_KEY_SIZE   = 0x91, /* Get keypad size. */
+    LM832x_CMD_READ_CFG                = 0x92, /* Get configuration item. */
+    LM832x_CMD_WRITE_CLOCK     = 0x93, /* Set clock config. */
+    LM832x_CMD_READ_CLOCK      = 0x94, /* Get clock config. */
+    LM832x_CMD_PWM_WRITE       = 0x95, /* Write PWM script. */
+    LM832x_CMD_PWM_START       = 0x96, /* Start PWM engine. */
+    LM832x_CMD_PWM_STOP                = 0x97, /* Stop PWM engine. */
+};
+
+#define LM832x_MAX_KPX         8
+#define LM832x_MAX_KPY         12
+
+static uint8_t lm_kbd_read(struct lm_kbd_s *s, int reg, int byte)
+{
+    int ret;
+
+    switch (reg) {
+    case LM832x_CMD_READ_ID:
+        ret = 0x0400;
+        break;
+
+    case LM832x_CMD_READ_INT:
+        ret = s->status;
+        if (!(s->status & INT_NOINIT)) {
+            s->status = 0;
+            lm_kbd_irq_update(s);
+        }
+        break;
+
+    case LM832x_CMD_READ_PORT_SEL:
+        ret = s->gpio.dir;
+        break;
+    case LM832x_CMD_READ_PORT_STATE:
+        ret = s->gpio.mask;
+        break;
+
+    case LM832x_CMD_READ_FIFO:
+        if (s->kbd.len <= 1)
+            return 0x00;
+
+        /* Example response from the two commands after a INT_KEYPAD
+         * interrupt caused by the key 0x3c being pressed:
+         * RPT_READ_FIFO: 55 bc 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01
+         *     READ_FIFO: bc 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01
+         * RPT_READ_FIFO: bc 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9 01
+         *
+         * 55 is the code of the key release event serviced in the previous
+         * interrupt handling.
+         *
+         * TODO: find out whether the FIFO is advanced a single character
+         * before reading every byte or the whole size of the FIFO at the
+         * last LM832x_CMD_READ_FIFO.  This affects LM832x_CMD_RPT_READ_FIFO
+         * output in cases where there are more than one event in the FIFO.
+         * Assume 0xbc and 0x3c events are in the FIFO:
+         * RPT_READ_FIFO: 55 bc 3c 00 4e ff 0a 50 08 00 29 d9 08 01 c9
+         *     READ_FIFO: bc 3c 00 00 4e ff 0a 50 08 00 29 d9 08 01 c9
+         * Does RPT_READ_FIFO now return 0xbc and 0x3c or only 0x3c?
+         */
+        s->kbd.start ++;
+        s->kbd.start &= sizeof(s->kbd.fifo) - 1;
+        s->kbd.len --;
+
+        return s->kbd.fifo[s->kbd.start];
+    case LM832x_CMD_RPT_READ_FIFO:
+        if (byte >= s->kbd.len)
+            return 0x00;
+
+        return s->kbd.fifo[(s->kbd.start + byte) & (sizeof(s->kbd.fifo) - 1)];
+
+    case LM832x_CMD_READ_ERROR:
+        return s->error;
+
+    case LM832x_CMD_READ_ROTATOR:
+        return 0;
+
+    case LM832x_CMD_READ_KEY_SIZE:
+        return s->kbd.size;
+
+    case LM832x_CMD_READ_CFG:
+        return s->config & 0xf;
+
+    case LM832x_CMD_READ_CLOCK:
+        return (s->clock & 0xfc) | 2;
+
+    default:
+        lm_kbd_error(s, ERR_CMDUNK);
+        fprintf(stderr, "%s: unknown command %02x\n", __FUNCTION__, reg);
+        return 0x00;
+    }
+
+    return ret >> (byte << 3);
+}
+
+static void lm_kbd_write(struct lm_kbd_s *s, int reg, int byte, uint8_t value)
+{
+    switch (reg) {
+    case LM832x_CMD_WRITE_CFG:
+        s->config = value;
+        /* This must be done whenever s->mux.in is updated (never).  */
+        if ((s->config >> 1) & 1)                      /* MUX1EN */
+            qemu_set_irq(s->mux.out[0], s->mux.in[0][(s->config >> 0) & 1]);
+        if ((s->config >> 3) & 1)                      /* MUX2EN */
+            qemu_set_irq(s->mux.out[0], s->mux.in[0][(s->config >> 2) & 1]);
+        /* TODO: check that this is issued only following the chip reset
+         * and not in the middle of operation and that it is followed by
+         * the GPIO ports re-resablishing through WRITE_PORT_SEL and
+         * WRITE_PORT_STATE (using a timer perhaps) and otherwise output
+         * warnings.  */
+        s->status = 0;
+        lm_kbd_irq_update(s);
+        s->kbd.len = 0;
+        s->kbd.start = 0;
+        s->reg = -1;
+        break;
+
+    case LM832x_CMD_RESET:
+        if (value == 0xaa)
+            lm_kbd_reset(s);
+        else
+            lm_kbd_error(s, ERR_BADPAR);
+        s->reg = -1;
+        break;
+
+    case LM823x_CMD_WRITE_PULL_DOWN:
+        if (!byte)
+            s->gpio.pull = value;
+        else {
+            s->gpio.pull |= value << 8;
+            lm_kbd_gpio_update(s);
+            s->reg = -1;
+        }
+        break;
+    case LM832x_CMD_WRITE_PORT_SEL:
+        if (!byte)
+            s->gpio.dir = value;
+        else {
+            s->gpio.dir |= value << 8;
+            lm_kbd_gpio_update(s);
+            s->reg = -1;
+        }
+        break;
+    case LM832x_CMD_WRITE_PORT_STATE:
+        if (!byte)
+            s->gpio.mask = value;
+        else {
+            s->gpio.mask |= value << 8;
+            lm_kbd_gpio_update(s);
+            s->reg = -1;
+        }
+        break;
+
+    case LM832x_CMD_SET_ACTIVE:
+        s->acttime = value;
+        s->reg = -1;
+        break;
+
+    case LM832x_CMD_SET_DEBOUNCE:
+        s->kbd.dbnctime = value;
+        s->reg = -1;
+        if (!value)
+            lm_kbd_error(s, ERR_BADPAR);
+        break;
+
+    case LM832x_CMD_SET_KEY_SIZE:
+        s->kbd.size = value;
+        s->reg = -1;
+        if (
+                        (value & 0xf) < 3 || (value & 0xf) > LM832x_MAX_KPY ||
+                        (value >> 4) < 3 || (value >> 4) > LM832x_MAX_KPX)
+            lm_kbd_error(s, ERR_BADPAR);
+        break;
+
+    case LM832x_CMD_WRITE_CLOCK:
+        s->clock = value;
+        s->reg = -1;
+        if ((value & 3) && (value & 3) != 3) {
+            lm_kbd_error(s, ERR_BADPAR);
+            fprintf(stderr, "%s: invalid clock setting in RCPWM\n",
+                            __FUNCTION__);
+        }
+        /* TODO: Validate that the command is only issued once */
+        break;
+
+    case LM832x_CMD_PWM_WRITE:
+        if (byte == 0) {
+            if (!(value & 3) || (value >> 2) > 59) {
+                lm_kbd_error(s, ERR_BADPAR);
+                s->reg = -1;
+                break;
+            }
+
+            s->pwm.faddr = value;
+            s->pwm.file[s->pwm.faddr] = 0;
+        } else if (byte == 1) {
+            s->pwm.file[s->pwm.faddr] |= value << 8;
+        } else if (byte == 2) {
+            s->pwm.file[s->pwm.faddr] |= value << 0;
+            s->reg = -1;
+        }
+        break;
+    case LM832x_CMD_PWM_START:
+        s->reg = -1;
+        if (!(value & 3) || (value >> 2) > 59) {
+            lm_kbd_error(s, ERR_BADPAR);
+            break;
+        }
+
+        s->pwm.addr[(value & 3) - 1] = value >> 2;
+        lm_kbd_pwm_start(s, (value & 3) - 1);
+        break;
+    case LM832x_CMD_PWM_STOP:
+        s->reg = -1;
+        if (!(value & 3)) {
+            lm_kbd_error(s, ERR_BADPAR);
+            break;
+        }
+
+        qemu_del_timer(s->pwm.tm[(value & 3) - 1]);
+        break;
+
+    case -1:
+        lm_kbd_error(s, ERR_BADPAR);
+        break;
+    default:
+        lm_kbd_error(s, ERR_CMDUNK);
+        fprintf(stderr, "%s: unknown command %02x\n", __FUNCTION__, reg);
+        break;
+    }
+}
+
+static void lm_i2c_event(i2c_slave *i2c, enum i2c_event event)
+{
+    struct lm_kbd_s *s = (struct lm_kbd_s *) i2c;
+
+    switch (event) {
+    case I2C_START_RECV:
+    case I2C_START_SEND:
+        s->i2c_cycle = 0;
+        s->i2c_dir = (event == I2C_START_SEND);
+        break;
+
+    default:
+        break;
+    }
+}
+
+static int lm_i2c_rx(i2c_slave *i2c)
+{
+    struct lm_kbd_s *s = (struct lm_kbd_s *) i2c;
+
+    return lm_kbd_read(s, s->reg, s->i2c_cycle ++);
+}
+
+static int lm_i2c_tx(i2c_slave *i2c, uint8_t data)
+{
+    struct lm_kbd_s *s = (struct lm_kbd_s *) i2c;
+
+    if (!s->i2c_cycle)
+        s->reg = data;
+    else
+        lm_kbd_write(s, s->reg, s->i2c_cycle - 1, data);
+    s->i2c_cycle ++;
+
+    return 0;
+}
+
+static void lm_kbd_save(QEMUFile *f, void *opaque)
+{
+    struct lm_kbd_s *s = (struct lm_kbd_s *) opaque;
+    int i;
+
+    i2c_slave_save(f, &s->i2c);
+    qemu_put_byte(f, s->i2c_dir);
+    qemu_put_byte(f, s->i2c_cycle);
+    qemu_put_byte(f, (uint8_t) s->reg);
+
+    qemu_put_8s(f, &s->config);
+    qemu_put_8s(f, &s->status);
+    qemu_put_8s(f, &s->acttime);
+    qemu_put_8s(f, &s->error);
+    qemu_put_8s(f, &s->clock);
+
+    qemu_put_be16s(f, &s->gpio.pull);
+    qemu_put_be16s(f, &s->gpio.mask);
+    qemu_put_be16s(f, &s->gpio.dir);
+    qemu_put_be16s(f, &s->gpio.level);
+
+    qemu_put_byte(f, s->kbd.dbnctime);
+    qemu_put_byte(f, s->kbd.size);
+    qemu_put_byte(f, s->kbd.start);
+    qemu_put_byte(f, s->kbd.len);
+    qemu_put_buffer(f, s->kbd.fifo, sizeof(s->kbd.fifo));
+
+    for (i = 0; i < sizeof(s->pwm.file); i ++)
+        qemu_put_be16s(f, &s->pwm.file[i]);
+    qemu_put_8s(f, &s->pwm.faddr);
+    qemu_put_buffer(f, s->pwm.addr, sizeof(s->pwm.addr));
+    qemu_put_timer(f, s->pwm.tm[0]);
+    qemu_put_timer(f, s->pwm.tm[1]);
+    qemu_put_timer(f, s->pwm.tm[2]);
+}
+
+static int lm_kbd_load(QEMUFile *f, void *opaque, int version_id)
+{
+    struct lm_kbd_s *s = (struct lm_kbd_s *) opaque;
+    int i;
+
+    i2c_slave_load(f, &s->i2c);
+    s->i2c_dir = qemu_get_byte(f);
+    s->i2c_cycle = qemu_get_byte(f);
+    s->reg = (int8_t) qemu_get_byte(f);
+
+    qemu_get_8s(f, &s->config);
+    qemu_get_8s(f, &s->status);
+    qemu_get_8s(f, &s->acttime);
+    qemu_get_8s(f, &s->error);
+    qemu_get_8s(f, &s->clock);
+
+    qemu_get_be16s(f, &s->gpio.pull);
+    qemu_get_be16s(f, &s->gpio.mask);
+    qemu_get_be16s(f, &s->gpio.dir);
+    qemu_get_be16s(f, &s->gpio.level);
+
+    s->kbd.dbnctime = qemu_get_byte(f);
+    s->kbd.size = qemu_get_byte(f);
+    s->kbd.start = qemu_get_byte(f);
+    s->kbd.len = qemu_get_byte(f);
+    qemu_get_buffer(f, s->kbd.fifo, sizeof(s->kbd.fifo));
+
+    for (i = 0; i < sizeof(s->pwm.file); i ++)
+        qemu_get_be16s(f, &s->pwm.file[i]);
+    qemu_get_8s(f, &s->pwm.faddr);
+    qemu_get_buffer(f, s->pwm.addr, sizeof(s->pwm.addr));
+    qemu_get_timer(f, s->pwm.tm[0]);
+    qemu_get_timer(f, s->pwm.tm[1]);
+    qemu_get_timer(f, s->pwm.tm[2]);
+
+    lm_kbd_irq_update(s);
+    lm_kbd_gpio_update(s);
+
+    return 0;
+}
+
+static int lm_kbd_iid = 0;
+
+struct i2c_slave *lm8323_init(i2c_bus *bus, qemu_irq nirq)
+{
+    struct lm_kbd_s *s;
+
+    s = (struct lm_kbd_s *) i2c_slave_init(bus, 0, sizeof(struct lm_kbd_s));
+    s->model = 0x8323;
+    s->pwm.tm[0] = qemu_new_timer(vm_clock, lm_kbd_pwm0_tick, s);
+    s->pwm.tm[1] = qemu_new_timer(vm_clock, lm_kbd_pwm1_tick, s);
+    s->pwm.tm[2] = qemu_new_timer(vm_clock, lm_kbd_pwm2_tick, s);
+    s->nirq = nirq;
+
+    s->i2c.event = lm_i2c_event;
+    s->i2c.recv = lm_i2c_rx;
+    s->i2c.send = lm_i2c_tx;
+
+    lm_kbd_reset(s);
+
+    qemu_register_reset((void *) lm_kbd_reset, s);
+    register_savevm("LM8323", lm_kbd_iid ++, 0,
+                    lm_kbd_save, lm_kbd_load, s);
+
+    return &s->i2c;
+}
+
+void lm832x_key_event(struct i2c_slave *i2c, int key, int state)
+{
+    struct lm_kbd_s *s = (struct lm_kbd_s *) i2c;
+
+    if ((s->status & INT_ERROR) && (s->error & ERR_FIFOOVR))
+        return;
+
+    if (s->kbd.len >= sizeof(s->kbd.fifo))
+        return lm_kbd_error(s, ERR_FIFOOVR);
+
+    s->kbd.fifo[(s->kbd.start + s->kbd.len ++) & (sizeof(s->kbd.fifo) - 1)] =
+            key | (state << 7);
+
+    /* We never set ERR_KEYOVR because we support multiple keys fine.  */
+    s->status |= INT_KEYPAD;
+    lm_kbd_irq_update(s);
+}

Modified: trunk/hw/nseries.c
===================================================================
--- trunk/hw/nseries.c  2008-05-09 20:13:43 UTC (rev 4399)
+++ trunk/hw/nseries.c  2008-05-09 22:16:11 UTC (rev 4400)
@@ -45,6 +45,7 @@
     i2c_bus *i2c;
 
     int keymap[0x80];
+    i2c_slave *kbd;
 
     struct tusb_s *usb;
     void *retu;
@@ -92,16 +93,22 @@
 #define N8X0_TAHVO_GPIO                        111
 #define N800_UNKNOWN_GPIO4             112     /* out */
 #define N810_SLEEPX_LED_GPIO           112
-#define N810_TSC_UNKNOWN_GPIO          118     /* out */
-#define N800_TSC_RESET_GPIO            119     /* ? */
+#define N800_TSC_RESET_GPIO            118     /* ? */
+#define N800_TSC_UNKNOWN_GPIO          119     /* out */
 #define N8X0_TMP105_GPIO               125
 
 /* Config */
 #define XLDR_LL_UART                   1
 
-/* Addresses on the I2C bus */
-#define N8X0_TMP105_ADDR               0x48
-#define N8X0_MENELAUS_ADDR             0x72
+/* Addresses on the I2C bus 0 */
+#define N810_TLV320AIC33_ADDR          0x18    /* Audio CODEC */
+#define N8X0_TCM825x_ADDR              0x29    /* Camera */
+#define N810_LP5521_ADDR               0x32    /* LEDs */
+#define N810_TSL2563_ADDR              0x3d    /* Light sensor */
+#define N810_LM8323_ADDR               0x45    /* Keyboard */
+/* Addresses on the I2C bus 1 */
+#define N8X0_TMP105_ADDR               0x48    /* Temperature sensor */
+#define N8X0_MENELAUS_ADDR             0x72    /* Power management */
 
 /* Chipselects on GPMC NOR interface */
 #define N8X0_ONENAND_CS                        0
@@ -190,12 +197,12 @@
     28,        /* Enter */
     77,        /* Right */
     -1,
-    1, /* Cycle (ESC) */
+     1,        /* Cycle (ESC) */
     80,        /* Down */
     62,        /* Menu (F4) */
     -1,
     66,        /* Zoom- (F8) */
-    64,        /* FS (F6) */
+    64,        /* FullScreen (F6) */
     65,        /* Zoom+ (F7) */
     -1,
 };
@@ -235,6 +242,107 @@
     tsc2005_set_transform(s->ts.opaque, &n810_pointercal);
 }
 
+/* N810 Keyboard controller */
+static void n810_key_event(void *opaque, int keycode)
+{
+    struct n800_s *s = (struct n800_s *) opaque;
+    int code = s->keymap[keycode & 0x7f];
+
+    if (code == -1) {
+        if ((keycode & 0x7f) == RETU_KEYCODE)
+            retu_key_event(s->retu, !(keycode & 0x80));
+        return;
+    }
+
+    lm832x_key_event(s->kbd, code, !(keycode & 0x80));
+}
+
+#define M      0
+
+static int n810_keys[0x80] = {
+    [0x01] = 16,       /* Q */
+    [0x02] = 37,       /* K */
+    [0x03] = 24,       /* O */
+    [0x04] = 25,       /* P */
+    [0x05] = 14,       /* Backspace */
+    [0x06] = 30,       /* A */
+    [0x07] = 31,       /* S */
+    [0x08] = 32,       /* D */
+    [0x09] = 33,       /* F */
+    [0x0a] = 34,       /* G */
+    [0x0b] = 35,       /* H */
+    [0x0c] = 36,       /* J */
+
+    [0x11] = 17,       /* W */
+    [0x12] = 62,       /* Menu (F4) */
+    [0x13] = 38,       /* L */
+    [0x14] = 40,       /* ' (Apostrophe) */
+    [0x16] = 44,       /* Z */
+    [0x17] = 45,       /* X */
+    [0x18] = 46,       /* C */
+    [0x19] = 47,       /* V */
+    [0x1a] = 48,       /* B */
+    [0x1b] = 49,       /* N */
+    [0x1c] = 42,       /* Shift (Left shift) */
+    [0x1f] = 65,       /* Zoom+ (F7) */
+
+    [0x21] = 18,       /* E */
+    [0x22] = 39,       /* ; (Semicolon) */
+    [0x23] = 12,       /* - (Minus) */
+    [0x24] = 13,       /* = (Equal) */
+    [0x2b] = 56,       /* Fn (Left Alt) */
+    [0x2c] = 50,       /* M */
+    [0x2f] = 66,       /* Zoom- (F8) */
+
+    [0x31] = 19,       /* R */
+    [0x32] = 29 | M,   /* Right Ctrl */
+    [0x34] = 57,       /* Space */
+    [0x35] = 51,       /* , (Comma) */
+    [0x37] = 72 | M,   /* Up */
+    [0x3c] = 82 | M,   /* Compose (Insert) */
+    [0x3f] = 64,       /* FullScreen (F6) */
+
+    [0x41] = 20,       /* T */
+    [0x44] = 52,       /* . (Dot) */
+    [0x46] = 77 | M,   /* Right */
+    [0x4f] = 63,       /* Home (F5) */
+    [0x51] = 21,       /* Y */
+    [0x53] = 80 | M,   /* Down */
+    [0x55] = 28,       /* Enter */
+    [0x5f] =  1,       /* Cycle (ESC) */
+
+    [0x61] = 22,       /* U */
+    [0x64] = 75 | M,   /* Left */
+
+    [0x71] = 23,       /* I */
+#if 0
+    [0x75] = 28 | M,   /* KP Enter (KP Enter) */
+#else
+    [0x75] = 15,       /* KP Enter (Tab) */
+#endif
+};
+
+#undef M
+
+static void n810_kbd_setup(struct n800_s *s)
+{
+    qemu_irq kbd_irq = omap2_gpio_in_get(s->cpu->gpif, N810_KEYBOARD_GPIO)[0];
+    int i;
+
+    for (i = 0; i < 0x80; i ++)
+        s->keymap[i] = -1;
+    for (i = 0; i < 0x80; i ++)
+        if (n810_keys[i] > 0)
+            s->keymap[n810_keys[i]] = i;
+
+    qemu_add_kbd_event_handler(n810_key_event, s);
+
+    /* Attach the LM8322 keyboard to the I2C bus,
+     * should happen in n8x0_i2c_setup and s->kbd be initialised here.  */
+    s->kbd = lm8323_init(s->i2c, kbd_irq);
+    i2c_set_slave_address(s->kbd, N810_LM8323_ADDR);
+}
+
 /* LCD MIPI DBI-C controller (URAL) */
 struct mipid_s {
     int resp[4];
@@ -954,8 +1062,10 @@
     n8x0_i2c_setup(s);
     if (model == 800)
         n800_tsc_kbd_setup(s);
-    else if (model == 810)
+    else if (model == 810) {
         n810_tsc_setup(s);
+        n810_kbd_setup(s);
+    }
     n8x0_spi_setup(s);
     n8x0_dss_setup(s, ds);
     n8x0_cbus_setup(s);






reply via email to

[Prev in Thread] Current Thread [Next in Thread]