Re: [Qemu-devel] [RESEND PATCH v5 4/4] vfio: Enable vfio-pci and mark supported

[Anthony Liguori]

Alex Williamson <address@hidden> writes:

> On Wed, 2012-09-26 at 08:50 -0500, Anthony Liguori wrote:
>> Alex Williamson <address@hidden> writes:
>> 
>> > Enabled for all softmmu guests supporting PCI on Linux hosts.  Note
>> > that currently only x86 hosts have the kernel side VFIO IOMMU support
>> > for this.  PPC (g3beige) is the only non-x86 guest known to work.
>> > ARM (veratile) hangs in firmware, others untested.
>> >
>> > Signed-off-by: Alex Williamson <address@hidden>
>> > Acked-by: Michael S. Tsirkin <address@hidden>
>> > ---
>> >
>> >  MAINTAINERS      |    5 +++++
>> >  configure        |    6 ++++++
>> >  hw/Makefile.objs |    3 ++-
>> >  3 files changed, 13 insertions(+), 1 deletion(-)
>> >
>> > diff --git a/MAINTAINERS b/MAINTAINERS
>> > index 25733fc..29aac4f 100644
>> > --- a/MAINTAINERS
>> > +++ b/MAINTAINERS
>> > @@ -474,6 +474,11 @@ M: Gerd Hoffmann <address@hidden>
>> >  S: Maintained
>> >  F: hw/usb*
>> >  
>> > +VFIO
>> > +M: Alex Williamson <address@hidden>
>> > +S: Supported
>> > +F: hw/vfio*
>> > +
>> >  vhost
>> >  M: Michael S. Tsirkin <address@hidden>
>> >  S: Supported
>> > diff --git a/configure b/configure
>> > index 1b86517..c2c0d4f 100755
>> > --- a/configure
>> > +++ b/configure
>> > @@ -165,6 +165,7 @@ attr=""
>> >  libattr=""
>> >  xfs=""
>> >  
>> > +vfio_pci="no"
>> >  vhost_net="no"
>> >  kvm="no"
>> >  gprof="no"
>> > @@ -509,6 +510,7 @@ Haiku)
>> >    usb="linux"
>> >    kvm="yes"
>> >    vhost_net="yes"
>> > +  vfio_pci="yes"
>> >    if [ "$cpu" = "i386" -o "$cpu" = "x86_64" ] ; then
>> >      audio_possible_drivers="$audio_possible_drivers fmod"
>> >    fi
>> > @@ -3174,6 +3176,7 @@ echo "libiscsi support  $libiscsi"
>> >  echo "build guest agent $guest_agent"
>> >  echo "seccomp support   $seccomp"
>> >  echo "coroutine backend $coroutine_backend"
>> > +echo "VFIO PCI support  $vfio_pci"
>> >  
>> >  if test "$sdl_too_old" = "yes"; then
>> >  echo "-> Your SDL version is too old - please upgrade to have SDL support"
>> > @@ -3911,6 +3914,9 @@ if test "$target_softmmu" = "yes" ; then
>> >    if test "$smartcard_nss" = "yes" ; then
>> >      echo "subdir-$target: subdir-libcacard" >> $config_host_mak
>> >    fi
>> > +  if test "$vfio_pci" = "yes" ; then
>> > +    echo "CONFIG_VFIO_PCI=y" >> $config_target_mak
>> > +  fi
>> >    case "$target_arch2" in
>> >      i386|x86_64)
>> >        echo "CONFIG_HAVE_CORE_DUMP=y" >> $config_target_mak
>> > diff --git a/hw/Makefile.objs b/hw/Makefile.objs
>> > index 6dfebd2..7f8d3e4 100644
>> > --- a/hw/Makefile.objs
>> > +++ b/hw/Makefile.objs
>> > @@ -198,7 +198,8 @@ obj-$(CONFIG_VGA) += vga.o
>> >  obj-$(CONFIG_SOFTMMU) += device-hotplug.o
>> >  obj-$(CONFIG_XEN) += xen_domainbuild.o xen_machine_pv.o
>> >  
>> > -# Inter-VM PCI shared memory
>> > +# Inter-VM PCI shared memory & VFIO PCI device assignment
>> >  ifeq ($(CONFIG_PCI), y)
>> >  obj-$(CONFIG_KVM) += ivshmem.o
>> > +obj-$(CONFIG_VFIO_PCI) += vfio_pci.o
>> 
>> Why not just make this
>> 
>> obj-$(CONFIG_LINUX) += vfio_pci.o
>> 
>> ?
>> 
>> All you're doing in configure is setting CONFIG_VFIO_PCI if
>> CONFIG_LINUX.
>
> Ok.  I thought I needed linux + softmmu + pci, but maybe the softmmu is
> implied with CONFIG_PCI?  Thanks,

obj-y is only used for softmmu so your covered.

Regards,

Anthony Liguori

>
> Alex
>
> --
> To unsubscribe from this list: send the line "unsubscribe kvm" in
> the body of a message to address@hidden
> More majordomo info at  http://vger.kernel.org/majordomo-info.html