qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PATCH 1/2] virtio-pci: reset all qbuses too when writing t


From: Paolo Bonzini
Subject: [Qemu-devel] [PATCH 1/2] virtio-pci: reset all qbuses too when writing to the status field
Date: Wed, 12 Dec 2012 15:26:35 +0100

virtio-pci devices do not perform a full reset when zero is written
to the status field.  While PCI-specific status is initialized, the
reset does not propagate down the qdev bus hierarchy.  Because of
this, a virtio reset does not cancel in-flight I/O for virtio-scsi
(where the cancellation is handled automatically by the SCSI
devices underneath virtio-scsi-pci).

The patch calls qdev_reset_all, which calls virtio_pci_reset,
instead of basically inlining the contents of the latter.

Reported-by: Bryan Venteicher <address@hidden>
Cc: Michael S. Tsirkin <address@hidden>
Signed-off-by: Paolo Bonzini <address@hidden>
---
 hw/virtio-pci.c | 25 ++++++++++---------------
 1 file changed, 10 insertions(+), 15 deletions(-)

diff --git a/hw/virtio-pci.c b/hw/virtio-pci.c
index 71f4fb5..a1685f1 100644
--- a/hw/virtio-pci.c
+++ b/hw/virtio-pci.c
@@ -268,12 +268,10 @@ static void virtio_ioport_write(void *opaque, uint32_t 
addr, uint32_t val)
     case VIRTIO_PCI_QUEUE_PFN:
         pa = (hwaddr)val << VIRTIO_PCI_QUEUE_ADDR_SHIFT;
         if (pa == 0) {
-            virtio_pci_stop_ioeventfd(proxy);
-            virtio_reset(proxy->vdev);
-            msix_unuse_all_vectors(&proxy->pci_dev);
-        }
-        else
+            qdev_reset_all(&proxy->pci_dev.qdev);
+        } else {
             virtio_queue_set_addr(vdev, vdev->queue_sel, pa);
+        }
         break;
     case VIRTIO_PCI_QUEUE_SEL:
         if (val < VIRTIO_PCI_QUEUE_MAX)
@@ -285,19 +283,16 @@ static void virtio_ioport_write(void *opaque, uint32_t 
addr, uint32_t val)
         }
         break;
     case VIRTIO_PCI_STATUS:
-        if (!(val & VIRTIO_CONFIG_S_DRIVER_OK)) {
-            virtio_pci_stop_ioeventfd(proxy);
-        }
-
         virtio_set_status(vdev, val & 0xFF);
 
-        if (val & VIRTIO_CONFIG_S_DRIVER_OK) {
-            virtio_pci_start_ioeventfd(proxy);
-        }
-
         if (vdev->status == 0) {
-            virtio_reset(proxy->vdev);
-            msix_unuse_all_vectors(&proxy->pci_dev);
+            qdev_reset_all(&proxy->pci_dev.qdev);
+        } else {
+            if (!(val & VIRTIO_CONFIG_S_DRIVER_OK)) {
+                virtio_pci_stop_ioeventfd(proxy);
+            } else {
+                virtio_pci_start_ioeventfd(proxy);
+            }
         }
 
         /* Linux before 2.6.34 sets the device as OK without enabling
-- 
1.8.0.1





reply via email to

[Prev in Thread] Current Thread [Next in Thread]