Re: [Qemu-devel] [Bug 1091766] Re: Physical host crash with Mellanox IB PCI passthrough

[Vlastimil Holer]

On Wed, Dec 19, 2012 at 5:46 PM, Alex Williamson
<address@hidden> wrote:
> You're right, I'm thinking of MSI where lspci reports x/y vectors.  The
> only way I know to get this is to grep /proc/interrupts on host and
> guest.  Look for kvm or vfio in the host and likely some device specific
> identifier in the guest.

You were absolutely right with vector counts. With VFIO I can see 4
and 4 vectors in host and guest and with legacy PCI assign. (on
qemu-1.0.1) I can see 30 in host and 4 in guest.

On Wed, Dec 19, 2012 at 11:46 PM, Alex Williamson
<address@hidden> wrote:
> Here's another version of the legacy pci-assign patch.  This should also
> only use 4 vectors on the host, like vfio.  I'm a little uneasy about
> setting up an MSIMessage with unknown data, but I guess we did it for a
> long time previously.  Please test.  Thanks

I have physical machine in production back again, so it'll take few
days to test your new patch. I'll let you know.

-- 
You received this bug notification because you are a member of qemu-
devel-ml, which is subscribed to QEMU.
https://bugs.launchpad.net/bugs/1091766

Title:
  Physical host crash with Mellanox IB PCI passthrough

Status in QEMU:
  New

Bug description:
  (from
  http://permalink.gmane.org/gmane.comp.emulators.kvm.devel/100736)

  We have been using PCI passthrough with the Mellanox IB interface
  (MT27500 Family [ConnectX-3]) on Debian 6.0.6, kernel 3.2.23 and
  qemu-kvm-1.0 (both from backports). It worked fine until latest
  update in backports to qemu-kvm-1.1.2. With newer qemu-kvm versions
  IB device probe in guest fails leaving firmware to kill whole physical 
machine.

  I have then compiled qemu-kvm from source, 1.0.1 was OK, 1.1.2 fails and
  even 1.2.0 fails as well. Our setup is based on IBM System X iDataPlex
  dx360 M4 Server.

  Note: Now I have also tested latest qemu-1.3.0 with linux 3.7.1 and
  new VFIO mechanism and behaves the same way.

  On guest the mlx4_core fails to probe device:
  | mlx4_core 0000:00:08.0: irq 74 for MSI/MSI-X
  | mlx4_core 0000:00:08.0: irq 75 for MSI/MSI-X
  | mlx4_core 0000:00:08.0: irq 76 for MSI/MSI-X
  | mlx4_core 0000:00:08.0: irq 77 for MSI/MSI-X
  | mlx4_core 0000:00:08.0: NOP command failed to generate MSI-X interrupt IRQ 
51).
  | mlx4_core 0000:00:08.0: Trying again without MSI-X.
  | mlx4_core 0000:00:08.0: NOP command failed to generate interrupt (IRQ 51), 
aborting.
  | mlx4_core 0000:00:08.0: BIOS or ACPI interrupt routing problem?
  | mlx4_core 0000:00:08.0: PCI INT A disabled
  | mlx4_core: probe of 0000:00:08.0 failed with error -16

  Which immediately results in reset of the whole physical machine:
  | Uhhuh. NMI received for unknown reason 3d on CPU 0.
  | Do you have a strange power saving mode enabled?
  | Dazed and confused, but trying to continue

  Followed by events in hardware management module:
  | A software NMI has occurred on system "SN# xxxxxxx"
  | Fault in slot "All PCI Err" on system "SN# xxxxxxx"
  | Fault in slot "PCI 1" on system "SN# xxxxxxx"
  | A Uncorrectable Bus Error has occurred on system "SN# xxxxxxx"
  | "Host Power" has been Power Cycled
  | System "SN# xxxxxxx" has recovered from an NMI

  Kernel logs for both host/guest machines and different qemu-kvm
  versions are attached. PCI passthrough for e.g. Intel e1000 works
  fine with all tested qemu-kvm versions.

To manage notifications about this bug go to:
https://bugs.launchpad.net/qemu/+bug/1091766/+subscriptions