[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-devel] use O_DIRECT to open disk images for IDE failed under xen-4
From: |
Gonglei (Arei) |
Subject: |
[Qemu-devel] use O_DIRECT to open disk images for IDE failed under xen-4.1.2 and qemu upstream |
Date: |
Thu, 23 May 2013 09:18:11 +0000 |
Hi, all
I use O_DIRECT to open disk images for IDE, but I'm failed. After debug, I get
the below logs:
[2013-05-22 23:25:46] ide: CMD=c8
[2013-05-22 23:25:46] bmdma: readb 0x00 : 0x08
[2013-05-22 23:25:46] bmdma: writeb 0x00 : 0x09
[2013-05-22 23:25:46] bmdma_cmd_writeb: 0x00000009
[2013-05-22 23:25:46] bmdma: readb 0x02 : 0x01
[2013-05-22 23:25:46] bmdma: readb 0x02 : 0x01
[2013-05-22 23:25:46] bmdma: readb 0x02 : 0x01
[2013-05-22 23:25:46] bmdma: readb 0x02 : 0x01
[2013-05-22 23:25:46] bmdma: readb 0x02 : 0x01
[2013-05-22 23:25:46] bmdma: readb 0x02 : 0x01
[2013-05-22 23:26:39] bmdma: writeb 0x00 : 0x08
[2013-05-22 23:26:39] bmdma_cmd_writeb: 0x00000008
[2013-05-22 23:26:56] ====== offset:0 buf:0x7ff100f21c00 count:512 aio_offset:0
[2013-05-22 23:31:30] ====== offset:0 buf:0x7ff100f21c00 count:512 aio_offset:0
[2013-05-22 23:31:30] ====== handle_aiocb_rw_linear errno: -14
[2013-05-22 23:31:30] ====== paio_complete errno=14
[2013-05-22 23:31:30] ====== ide_dma_error!!!
[2013-05-22 23:31:30] ide: read status addr=0x3f6 val=41
QEMU command line :
qemu-system-i386 -xen-domid 837 -chardev
socket,id=libxl-cmd,path=/var/run/xen/qmp-libxl-837,server,nowait -mon
chardev=libxl-cmd,mode=control -name suse11 -vnc 0.0.0.0:1 -serial pty -boot
order=c -usb -usbdevice tablet -smp 2,maxcpus=2 -device
rtl8139,id=nic0,netdev=net0,mac=00:16:3e:13:d3:72 -netdev
type=tap,id=net0,ifname=tap837.0,downscript=no -M xenfv -m 2040 -drive
file=/mnt/sdd/image/suse.image,if=ide,index=0,media=disk,format=raw,cache=none
errno 14 shows Bad Address. And I find QEMU_AIO_MISALIGNED flag bit is not set
through debug.
/*
* If O_DIRECT is used the buffer needs to be aligned on a sector
* boundary. Check if this is the case or tell the low-level
* driver that it needs to copy the buffer.
*/
if ((bs->open_flags & BDRV_O_NOCACHE)) {
if (!bdrv_qiov_is_aligned(bs, qiov)) { //if the address is
aligned-512, will no meet the conditions
type |= QEMU_AIO_MISALIGNED;
#ifdef CONFIG_LINUX_AIO
} else if (s->use_aio) {
return laio_submit(bs, s->aio_ctx, s->fd, sector_num, qiov,
nb_sectors, cb, opaque, type);
#endif
Next process:
static ssize_t handle_aiocb_rw(struct qemu_paiocb *aiocb)
{
ssize_t nbytes;
char *buf;
if (!(aiocb->aio_type & QEMU_AIO_MISALIGNED)) {
/*
* If there is just a single buffer, and it is properly aligned
* we can just use plain pread/pwrite without any problems.
*/
if (aiocb->aio_niov == 1)
return handle_aiocb_rw_linear(aiocb, aiocb->aio_iov->iov_base);
//this way, and reports errno 14 next
Anyone have a good method to resolve this bug? Thanks!
Best Regards!
-Gonglei
- [Qemu-devel] use O_DIRECT to open disk images for IDE failed under xen-4.1.2 and qemu upstream,
Gonglei (Arei) <=
- Re: [Qemu-devel] use O_DIRECT to open disk images for IDE failed under xen-4.1.2 and qemu upstream, Stefano Stabellini, 2013/05/23
- Re: [Qemu-devel] use O_DIRECT to open disk images for IDE failed under xen-4.1.2 and qemu upstream, Gonglei (Arei), 2013/05/23
- Re: [Qemu-devel] use O_DIRECT to open disk images for IDE failed under xen-4.1.2 and qemu upstream, Stefan Hajnoczi, 2013/05/24
- Re: [Qemu-devel] use O_DIRECT to open disk images for IDE failed under xen-4.1.2 and qemu upstream, Gonglei (Arei), 2013/05/25
- Re: [Qemu-devel] use O_DIRECT to open disk images for IDE failed under xen-4.1.2 and qemu upstream, Stefan Hajnoczi, 2013/05/27
- Re: [Qemu-devel] [Xen-devel] use O_DIRECT to open disk images for IDE failed under xen-4.1.2 and qemu upstream, Konrad Rzeszutek Wilk, 2013/05/28