[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-devel] [PATCH RFC] e1000: defer packets until BM enabled
From: |
Gabriel Somlo |
Subject: |
Re: [Qemu-devel] [PATCH RFC] e1000: defer packets until BM enabled |
Date: |
Mon, 1 Dec 2014 18:01:18 +0000 |
Hi Michael,
I had to make some small changes to get this patch to build successfully,
see inline below:
On Monday, December 01, 2014 11:50am, Michael S. Tsirkin address@hidden wrote:
>
> Some guests seem to set BM for e1000 after
> enabling RX.
> If packets arrive in the window, device is wedged.
> Probably works by luck on real hardware, work around
> this by making can_receive depend on BM.
>
> Signed-off-by: Michael S. Tsirkin <address@hidden>
> ---
> hw/net/e1000.c | 20 +++++++++++++++++++-
> 1 file changed, 19 insertions(+), 1 deletion(-)
>
> diff --git a/hw/net/e1000.c b/hw/net/e1000.c
> index e33a4da..34625ac 100644
> --- a/hw/net/e1000.c
> +++ b/hw/net/e1000.c
> @@ -923,7 +923,9 @@ e1000_can_receive(NetClientState *nc)
> E1000State *s = qemu_get_nic_opaque(nc);
>
> return (s->mac_reg[STATUS] & E1000_STATUS_LU) &&
> - (s->mac_reg[RCTL] & E1000_RCTL_EN) && e1000_has_rxbufs(s, 1);
> + (s->mac_reg[RCTL] & E1000_RCTL_EN) &&
> + (s->parent_obj.config[PCI_COMMAND] & PCI_COMMAND_MASTER) &&
> + e1000_has_rxbufs(s, 1);
> }
>
> static uint64_t rx_desc_base(E1000State *s)
> @@ -1529,6 +1531,20 @@ static NetClientInfo net_e1000_info = {
> .link_status_changed = e1000_set_link_status,
> };
>
> +static void e1000_write_config(PCIDevice *pci_dev, uint32_t address,
> + uint32_t val, int len)
> +{
> + E1000State *d = E1000(dev);
s/dev/pci_dev/
> +
> + pci_default_write_config(pci_dev, address, val, len);
> +
> + if (range_covers_byte(address, len, PCI_COMMAND) &&
requires #include "qemu/range.h" at the top of e1000.c
> + (pci_dev->config[PCI_COMMAND] & PCI_COMMAND_MASTER)) {
> + qemu_flush_queued_packets(qemu_get_queue(s->nic));
s/s->nic/d->nic/
> + }
> +}
> +
> +
> static int pci_e1000_init(PCIDevice *pci_dev)
> {
> DeviceState *dev = DEVICE(pci_dev);
> @@ -1539,6 +1555,8 @@ static int pci_e1000_init(PCIDevice *pci_dev)
> int i;
> uint8_t *macaddr;
>
> + pci_dev->config_write = e1000_write_config;
> +
> pci_conf = pci_dev->config;
>
> /* TODO: RST# value should be 0, PCI spec 6.2.4 */
> --
With this, I can confirm everything still works fine on both Mavericks and
F21-beta-live. So:
Tested-by: Gabriel Somlo <address@hidden>
Regards,
--Gabriel