[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Qemu-devel] [PATCH 2/2] docs: add memory-hotplug.txt
From: |
Luiz Capitulino |
Subject: |
Re: [Qemu-devel] [PATCH 2/2] docs: add memory-hotplug.txt |
Date: |
Tue, 3 Mar 2015 11:16:20 -0500 |
On Tue, 03 Mar 2015 16:12:58 +0100
Paulo Ricardo Paz Vital <address@hidden> wrote:
> On Tue, 2015-03-03 at 09:47 -0500, Luiz Capitulino wrote:
> > This document describes how to use memory hotplug in QEMU.
> >
> > Signed-off-by: Luiz Capitulino <address@hidden>
> > ---
> > docs/memory-hotplug.txt | 76
> > +++++++++++++++++++++++++++++++++++++++++++++++++
> > 1 file changed, 76 insertions(+)
> > create mode 100644 docs/memory-hotplug.txt
> >
> > diff --git a/docs/memory-hotplug.txt b/docs/memory-hotplug.txt
> > new file mode 100644
> > index 0000000..f70571d
> > --- /dev/null
> > +++ b/docs/memory-hotplug.txt
> > @@ -0,0 +1,76 @@
> > +QEMU memory hotplug
> > +===================
> > +
> > +This document explains how to use the memory hotplug feature in QEMU,
> > +which is present since v2.1.0.
> > +
> > +Please, note that memory hotunplug is not supported yet. This means
> > +that you're able to add memory, but you're not able to remove it.
> > +Also, proper guest support is required for memory hotplug to work.
> > +
> > +Basic RAM hotplug
> > +-----------------
> > +
> > +In order to be able to hotplug memory, QEMU has to be told how many
> > +hotpluggable memory slots to create and what is the maximum amount of
> > +memory the guest can grow. This is done at startup time by means of
>
> Igor suggested to s/grow/have in the line below, but I think you can
> change here also.
Right. If this is the only change required, then the maintainer could
change it when applying the series.
>
> > +the -m command-line option, which has the following format:
> > +
> > + -m [size=]megs[,slots=n,maxmem=size]
> > +
> > +Where,
> > +
> > + - "megs" is the startup RAM. It is the RAM the guest will boot with
>
> Here, for me, the sentence "It is the RAM the guest will boot with" is
> not necessary, since the first sentence ("is the startup RAM") already
> explain that VM will start with this amount of RAM.
I'm not strong about this, but I think that the term "startup RAM"
might not be obvious to everyone at first so I think it doesn't hurt
to define what it means in this context.
>
> > + - "slots" is the number of hotpluggable memory slots
> > + - "maxmem" is the maximum RAM size the guest can have
> > +
> > +For example, the following command-line:
> > +
> > + qemu [...] 1G,slots=3,maxmem=4G
> > +
> > +Creates a guest with 1GB of memory and three hotpluggable memory slots.
> > +The hotpluggable memory slots are empty when the guest is booted, so all
> > +memory the guest will see after boot is 1GB. The maximum memory the
> > +guest can reach is 4GB. This means that three additional gigabytes can be
> > +hotplugged by using any combination of the available memory slots.
> > +
> > +Two monitor commands are used to hotplug memory:
> > +
> > + - "object_add": creates a memory backend object
> > + - "device_add": creates a front-end pc-dimm device and inserts it
> > + into the first empty slot
> > +
> > +For example, the following commands add another 1GB to the guest
> > +discussed earlier:
> > +
> > + (qemu) object_add memory-backend-ram,id=mem1,size=1G
> > + (qemu) device_add pc-dimm,id=dimm1,memdev=mem1
> > +
> > +Using the file backend
> > +----------------------
> > +
> > +Besides basic RAM hotplug, QEMU also supports using files as a memory
> > +backend. This is useful for using hugetlbfs in Linux, which provides
> > +access to bigger page sizes.
> > +
> > +For example, assuming that the host has 1GB hugepages available in
> > +the /mnt/hugepages-1GB directory, a 1GB hugepage could be hotplugged
> > +into the guest from the previous section with the following commands:
> > +
> > + (qemu) object_add
> > memory-backend-file,id=mem1,size=1G,mem-path=/mnt/hugepages-1GB
> > + (qemu) device_add pc-dimm,id=dimm1,memdev=mem1
> > +
> > +It's also possible to start a guest with memory cold-plugged into the
> > +hotpluggable memory slots. This might seem counterintuitive at first,
> > +but this allows for a lot of flexibility when using the file backend.
> > +
> > +In the following command-line example, a 8GB guest is created where 6GB
> > +comes from regular RAM, 1GB is a 1GB hugepage page and 256MB is from
> > +2MB pages. Also, the guest has additional memory slots to hotplug more
> > +2GB if needed:
> > +
> > + qemu [...] -m 6GB,slots=4,maxmem=10G \
> > + -object memory-backend-file,id=mem1,size=1G,mem-path=/mnt/hugepages-1G \
> > + -device pc-dimm,id=dimm1,memdev=mem1 \
> > + -object
> > memory-backend-file,id=mem2,size=256M,mem-path=/mnt/hugepages-2MB \
> > + -device pc-dimm,id=dimm2,memdev=mem2
>
[Qemu-devel] [PATCH 1/2] qemu-options.hx: improve -m description, Luiz Capitulino, 2015/03/03