qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Qemu-devel] [PATCH v2 1/3] cpu: Provide vcpu throttling interface


From: Jason J. Herne
Subject: Re: [Qemu-devel] [PATCH v2 1/3] cpu: Provide vcpu throttling interface
Date: Mon, 08 Jun 2015 15:07:12 -0400
User-agent: Mozilla/5.0 (X11; Linux x86_64; rv:31.0) Gecko/20100101 Thunderbird/31.5.0

On 06/03/2015 02:11 PM, Jason J. Herne wrote:
On 06/03/2015 02:03 PM, Dr. David Alan Gilbert wrote:
* Jason J. Herne (address@hidden) wrote:
On 06/03/2015 03:56 AM, Juan Quintela wrote:
"Jason J. Herne" <address@hidden> wrote:
...
We are checking for throotling on each cpu each 10ms.
But on patch 2 we can see that we only change the throotling each
time that we call migration_bitmap_sync(), that only happens each round
through all the pages. Normally auto-converge only matters for machines
with lots of memory, so this is going to happen each more than 10ms (we
change it each 4 passes).  You changed it to each 2 passes, and you add
it a 0.2.  I think  that I would preffer to just have it each single
pass, but add a 0.1 each pass?  simpler and end result would be the
same?



Well, we certainly could make it run every pass but I think it would get
a little too aggressive then. The reason is, we do not increment the
throttle
rate by adding 0.2 each time. We increment it by multiplying the current
rate
by 2. So by doing that every pass we are doubling the exponential growth
rate. I will admit the numbers I chose are hardly scientific... I
chose them
because they seemed to provide a decent balance of "throttling
aggression"
in
my workloads.

That's the advantage of making them parameters.

I see your point. Expecting the user to configure these parameters
seems a bit much. But I guess, in theory, it is better to have the
ability to change them and not need it, than need it and not have it
right?

So, as you stated earlier these should hook into MigrationParams
somehow? I'll admit this is the first I've seen this construct. If
this is the optimal location for the two controls (x-throttle-initial,
x-throttle-multiplier?) I can add them there. Will keep defaults of
0.2 for initial and 2.0 for multiplier(is there a better name?)?


So I'm attempting add the initial throttle value and the multiplier to MigrationParameters and I've come across a problem. hmp_migrate_set_parameter assumes all parameters are ints. Apparently floating point is not allowed...

    void hmp_migrate_set_parameter(Monitor *mon, const QDict *qdict)
    {
        const char *param = qdict_get_str(qdict, "parameter");
        int value = qdict_get_int(qdict, "value");

Also from hmp-commands.hx

    {
        .name       = "migrate_set_parameter",
        .args_type  = "parameter:s,value:i",
        .params     = "parameter value",
        .help       = "Set the parameter for migration",
        .mhandler.cmd = hmp_migrate_set_parameter,
        .command_completion = migrate_set_parameter_completion,
    },

I'm hoping someone already has an idea for dealing with this problem? If not, I suppose this is a good add-on for Dave's discussion on redesigning MigrationParameters.

--
-- Jason J. Herne (address@hidden)




reply via email to

[Prev in Thread] Current Thread [Next in Thread]