qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PULL 5/7] hw/intc/arm_gic_common.c: Reset all registers


From: Peter Maydell
Subject: [Qemu-devel] [PULL 5/7] hw/intc/arm_gic_common.c: Reset all registers
Date: Mon, 6 Jul 2015 10:59:33 +0100

The arm_gic_common reset function was missing reset code for
several of the GIC's state fields:
 * bpr[]
 * abpr[]
 * priority1[]
 * priority2[]
 * sgi_pending[]
 * irq_target[] (SMP configurations only)

These probably went unnoticed because most guests will either
never touch them, or will write to them in the process of
configuring the GIC before enabling interrupts.

Signed-off-by: Peter Maydell <address@hidden>
Message-id: address@hidden
Reviewed-by: Edgar E. Iglesias <address@hidden>
---
 hw/intc/arm_gic_common.c | 21 ++++++++++++++++++---
 1 file changed, 18 insertions(+), 3 deletions(-)

diff --git a/hw/intc/arm_gic_common.c b/hw/intc/arm_gic_common.c
index 044ad66..a64d071 100644
--- a/hw/intc/arm_gic_common.c
+++ b/hw/intc/arm_gic_common.c
@@ -123,7 +123,7 @@ static void arm_gic_common_realize(DeviceState *dev, Error 
**errp)
 static void arm_gic_common_reset(DeviceState *dev)
 {
     GICState *s = ARM_GIC_COMMON(dev);
-    int i;
+    int i, j;
     memset(s->irq_state, 0, GIC_MAXIRQ * sizeof(gic_irq_state));
     for (i = 0 ; i < s->num_cpu; i++) {
         if (s->revision == REV_11MPCORE) {
@@ -135,15 +135,30 @@ static void arm_gic_common_reset(DeviceState *dev)
         s->running_irq[i] = 1023;
         s->running_priority[i] = 0x100;
         s->cpu_ctlr[i] = 0;
+        s->bpr[i] = GIC_MIN_BPR;
+        s->abpr[i] = GIC_MIN_ABPR;
+        for (j = 0; j < GIC_INTERNAL; j++) {
+            s->priority1[j][i] = 0;
+        }
+        for (j = 0; j < GIC_NR_SGIS; j++) {
+            s->sgi_pending[j][i] = 0;
+        }
     }
     for (i = 0; i < GIC_NR_SGIS; i++) {
         GIC_SET_ENABLED(i, ALL_CPU_MASK);
         GIC_SET_EDGE_TRIGGER(i);
     }
-    if (s->num_cpu == 1) {
+
+    for (i = 0; i < ARRAY_SIZE(s->priority2); i++) {
+        s->priority2[i] = 0;
+    }
+
+    for (i = 0; i < GIC_MAXIRQ; i++) {
         /* For uniprocessor GICs all interrupts always target the sole CPU */
-        for (i = 0; i < GIC_MAXIRQ; i++) {
+        if (s->num_cpu == 1) {
             s->irq_target[i] = 1;
+        } else {
+            s->irq_target[i] = 0;
         }
     }
     s->ctlr = 0;
-- 
1.9.1




reply via email to

[Prev in Thread] Current Thread [Next in Thread]