> > > > > > >Maxime Coquelin<address@hidden> writes:
> > > > > > >
> > > > > > > >On 11/18/2016 07:15 PM, Aaron Conole wrote:
> > > > > > > > >Maxime Coquelin<address@hidden> writes:
> > > > > > > > >
> > > > > > > > > >This series implements Virtio spec update from Aaron Conole
which
> > > > > > > > > >defines a way for the host to expose its max MTU to the
guest.
> > > > > > > > > >
> > > > > > > > > >Changes since RFC v1:
> > > > > > > > > >---------------------
> > > > > > > > > > - Rebased on top of v2.8.0-rc0 (2.7.90)
> > > > > > > > > > - Write MTU unconditionnaly in netcfg to avoid memory
leak (Paolo)
> > > > > > > > > > - Add host_mtu property to be able to disable the feature
from QEMU
> > > > > > > > > >
> > > > > > > > > >Maxime Coquelin (3):
> > > > > > > > > > vhost-user: Add new protocol feature MTU
> > > > > > > > > > vhost-net: Add new MTU feature support
> > > > > > > > > > virtio-net: Add MTU feature support
> > > > > > > > > >
> > > > > > > > > > hw/net/vhost_net.c | 11 +++++++++++
> > > > > > > > > > hw/net/virtio-net.c | 14 ++++++++++++++
> > > > > > > > > > hw/virtio/vhost-user.c | 11 +++++++++++
> > > > > > > > > > include/hw/virtio/vhost.h | 1 +
> > > > > > > > > > include/hw/virtio/virtio-net.h | 1 +
> > > > > > > > > > include/net/vhost_net.h | 2 ++
> > > > > > > > > > 6 files changed, 40 insertions(+)
> > > > > > > > >I ran this with a VM, but it seems the offered maximum MTU was
of
> > > > > > > > >value
> > > > > > > > >0 - is this expected with this version? How can I change the
offered
> > > > > > > > >value? Sorry, I'm not as familiar with QEMU/libvirt side of
the
> > > > > > > > >world.
> > > > > > > >They way I implemented it, the MTU value is to be provided by
> > > > > > > >vhost-user process (e.g. OVS/DPDK). I added a Vhost protocol
> > > > > > > >feature for this. The sequence is:
> > > > > > > >1. Qemu send VHOST_USER_GET_PROTOCOL_FEATURES request
> > > > > > > >2. DPDK replies with providing supported features
> > > > > > > >3. If DPDK supports VHOST_USER_PROTOCOL_F_MTU, Qemu send
> > > > > > > > VHOST_USER_GET_MTU resuest
> > > > > > > >4. DPDK replies with MTU value
> > > > > > > >
> > > > > > > >Does that make sense?
> > > > > > >In the case of a vhost-user backed port, yes (so for instance, if
I use
> > > > > > >ovs+dpdk vhost-user in client or server mode). However, what
about the
> > > > > > >non-dpdk case, where I still use a virtio-net driver in kernel and
want
> > > > > > >to have it backed with, say, a tap device in the host attached to
> > > > > > >virbr0 (or some other bridge). It should still pull the mtu from
that
> > > > > > >device and offer it, I think.
> > > > > > >
> > > > > > > >Another possibility would be that we could directly pass the MTU
value
> > > > > > > >to Qemu. It may be easier to implement, and to handle migration.
> > > > > > > >Problem is that if we do this, this is not the vSwitch that
decides the
> > > > > > > >MTU to set.
> > > > > > >Might be better to determined the mtu by looking at what actually
> > > > > > >provides the back-end for the networking.
> > > > > > >
> > > > > > > >Regards,
> > > > > > > >Maxime