qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PATCH for-2.8] spapr: fix default DRC state for coldplugge


From: Michael Roth
Subject: [Qemu-devel] [PATCH for-2.8] spapr: fix default DRC state for coldplugged LMBs
Date: Wed, 30 Nov 2016 17:05:34 -0600

Currently we set the initial isolation/allocation state for DRCs
associated with coldplugged LMBs to ISOLATED/UNUSABLE,
respectively, under the assumption that the guest will move this
state to UNISOLATED/USABLE.

In fact, this is only the case for LMBs added via hotplug. For
coldplugged LMBs, the guest actually assumes the initial state to
be UNISOLATED/USABLE.

In practice, this only becomes an issue when we attempt to unplug
one of these LMBs, where the guest kernel will issue an
rtas-get-sensor-state call to check that the corresponding DRC is
in an USABLE state before it will release the LMB back to
QEMU. If the returned state is otherwise, the guest will assume no
further action is needed, which bypasses the QEMU-side cleanup that
occurs during the USABLE->UNUSABLE transition. This results in
LMBs and their corresponding pc-dimm devices to stick around
indefinitely.

This patch fixes the issue by manually setting DRCs associated with
cold-plugged LMBs to UNISOLATED/ALLOCATED, but leaving the hotplug
state untouched. As it turns out, this is analogous to the handling
for cold-plugged CPUs in spapr_core_plug().

Cc: address@hidden
Cc: David Gibson <address@hidden>
Cc: Bharata B Rao <address@hidden>
Cc: Greg Kurz <address@hidden>
Signed-off-by: Michael Roth <address@hidden>
---
This patch is a revision to the previously posted series:

  [PATCH for-2.8 0/3] spapr: fix breakage of memory unplug after migration

That patchset introduced DRC migration as a means to address DRC state
synchronization between source/target to allow memory unplug after
migration. It turns out that unplug was also not working for LMBs
that were defined on the source via '-device pc-dimm'. The real issue
was that the default coldplug state on *both* the source and target was
wrong, and by fixing that default state, we no longer need DRC migration
for the scenario mentioned in the previous patchset since, incidentally,
coldplug state on the target now matches post-hotplug DRC state on the
source.

This patch is very late for 2.8, but I'm hoping it can still make it
in for rc3/2.8.

I've tested forward/backward migration for all possible combinations
(other than known case unsupported case 2.8->2.7) of
v2.6/v2.7/v2.8, pseries-2.6/pseries-2.7/pseries-2.8, and
modern-hotplug-events=true/false, with various combinations of
CPU / LMB hotplug/unplug before/after migration.
---
 hw/ppc/spapr.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/hw/ppc/spapr.c b/hw/ppc/spapr.c
index c3269c7..208ef7b 100644
--- a/hw/ppc/spapr.c
+++ b/hw/ppc/spapr.c
@@ -2290,6 +2290,11 @@ static void spapr_add_lmbs(DeviceState *dev, uint64_t 
addr_start, uint64_t size,
         drck = SPAPR_DR_CONNECTOR_GET_CLASS(drc);
         drck->attach(drc, dev, fdt, fdt_offset, !dev->hotplugged, errp);
         addr += SPAPR_MEMORY_BLOCK_SIZE;
+        if (!dev->hotplugged) {
+            /* guests expect coldplugged LMBs to be pre-allocated */
+            drck->set_allocation_state(drc, SPAPR_DR_ALLOCATION_STATE_USABLE);
+            drck->set_isolation_state(drc, 
SPAPR_DR_ISOLATION_STATE_UNISOLATED);
+        }
     }
     /* send hotplug notification to the
      * guest only in case of hotplugged memory
-- 
1.9.1




reply via email to

[Prev in Thread] Current Thread [Next in Thread]