[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Qemu-devel] [PATCH] rtl8139: correctly handle PHY reset
From: |
Hervé Poussineau |
Subject: |
[Qemu-devel] [PATCH] rtl8139: correctly handle PHY reset |
Date: |
Tue, 13 Dec 2016 20:44:41 +0100 |
According to datasheet:
"[Bit 15 of Basic Mode Control Register] sets the status and control registers
of the PHY (register 0062-0074) in a default state. This bit is self-clearing.
1 = software reset; 0 = normal operation."
This fixes the netcard detection failure in Minoca OS.
Signed-off-by: Hervé Poussineau <address@hidden>
---
hw/net/rtl8139.c | 34 +++++++++++++++++++++-------------
1 file changed, 21 insertions(+), 13 deletions(-)
diff --git a/hw/net/rtl8139.c b/hw/net/rtl8139.c
index f05e59c..671c7e4 100644
--- a/hw/net/rtl8139.c
+++ b/hw/net/rtl8139.c
@@ -1205,6 +1205,20 @@ static void rtl8139_reset_rxring(RTL8139State *s,
uint32_t bufferSize)
s->RxBufAddr = 0;
}
+static void rtl8139_reset_phy(RTL8139State *s)
+{
+ s->BasicModeStatus = 0x7809;
+ s->BasicModeStatus |= 0x0020; /* autonegotiation completed */
+ /* preserve link state */
+ s->BasicModeStatus |= qemu_get_queue(s->nic)->link_down ? 0 : 0x04;
+
+ s->NWayAdvert = 0x05e1; /* all modes, full duplex */
+ s->NWayLPAR = 0x05e1; /* all modes, full duplex */
+ s->NWayExpansion = 0x0001; /* autonegotiation supported */
+
+ s->CSCR = CSCR_F_LINK_100 | CSCR_HEART_BIT | CSCR_LD;
+}
+
static void rtl8139_reset(DeviceState *d)
{
RTL8139State *s = RTL8139(d);
@@ -1256,25 +1270,14 @@ static void rtl8139_reset(DeviceState *d)
s->Config3 = 0x1; /* fast back-to-back compatible */
s->Config5 = 0x0;
- s->CSCR = CSCR_F_LINK_100 | CSCR_HEART_BIT | CSCR_LD;
-
s->CpCmd = 0x0; /* reset C+ mode */
s->cplus_enabled = 0;
-
// s->BasicModeCtrl = 0x3100; // 100Mbps, full duplex, autonegotiation
// s->BasicModeCtrl = 0x2100; // 100Mbps, full duplex
s->BasicModeCtrl = 0x1000; // autonegotiation
- s->BasicModeStatus = 0x7809;
- //s->BasicModeStatus |= 0x0040; /* UTP medium */
- s->BasicModeStatus |= 0x0020; /* autonegotiation completed */
- /* preserve link state */
- s->BasicModeStatus |= qemu_get_queue(s->nic)->link_down ? 0 : 0x04;
-
- s->NWayAdvert = 0x05e1; /* all modes, full duplex */
- s->NWayLPAR = 0x05e1; /* all modes, full duplex */
- s->NWayExpansion = 0x0001; /* autonegotiation supported */
+ rtl8139_reset_phy(s);
/* also reset timer and disable timer interrupt */
s->TCTR = 0;
@@ -1469,7 +1472,7 @@ static void rtl8139_BasicModeCtrl_write(RTL8139State *s,
uint32_t val)
DPRINTF("BasicModeCtrl register write(w) val=0x%04x\n", val);
/* mask unwritable bits */
- uint32_t mask = 0x4cff;
+ uint32_t mask = 0xccff;
if (1 || !rtl8139_config_writable(s))
{
@@ -1479,6 +1482,11 @@ static void rtl8139_BasicModeCtrl_write(RTL8139State *s,
uint32_t val)
mask |= 0x0100;
}
+ if (val & 0x8000) {
+ /* Reset PHY */
+ rtl8139_reset_phy(s);
+ }
+
val = SET_MASKED(val, mask, s->BasicModeCtrl);
s->BasicModeCtrl = val;
--
2.1.4
- [Qemu-devel] [PATCH] rtl8139: correctly handle PHY reset,
Hervé Poussineau <=