qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Qemu-devel] [PATCH v4 14/29] libvhost-user+postcopy: Register new r


From: Peter Xu
Subject: Re: [Qemu-devel] [PATCH v4 14/29] libvhost-user+postcopy: Register new regions with the ufd
Date: Tue, 13 Mar 2018 16:28:01 +0800
User-agent: Mutt/1.9.1 (2017-09-22)

On Mon, Mar 12, 2018 at 01:23:21PM +0000, Dr. David Alan Gilbert wrote:
> * Peter Xu (address@hidden) wrote:
> > On Thu, Mar 08, 2018 at 07:57:56PM +0000, Dr. David Alan Gilbert (git) 
> > wrote:
> > > From: "Dr. David Alan Gilbert" <address@hidden>
> > > 
> > > When new regions are sent to the client using SET_MEM_TABLE, register
> > > them with the userfaultfd.
> > > 
> > > Signed-off-by: Dr. David Alan Gilbert <address@hidden>
> > > ---
> > >  contrib/libvhost-user/libvhost-user.c | 34 
> > > ++++++++++++++++++++++++++++++++++
> > >  1 file changed, 34 insertions(+)
> > > 
> > > diff --git a/contrib/libvhost-user/libvhost-user.c 
> > > b/contrib/libvhost-user/libvhost-user.c
> > > index 4922b2c722..a18bc74a7c 100644
> > > --- a/contrib/libvhost-user/libvhost-user.c
> > > +++ b/contrib/libvhost-user/libvhost-user.c
> > > @@ -494,6 +494,40 @@ vu_set_mem_table_exec_postcopy(VuDev *dev, 
> > > VhostUserMsg *vmsg)
> > >          close(vmsg->fds[i]);
> > >      }
> > >  
> > > +    /* TODO: Get address back to QEMU */
> > > +    for (i = 0; i < dev->nregions; i++) {
> > > +        VuDevRegion *dev_region = &dev->regions[i];
> > > +#ifdef UFFDIO_REGISTER
> > > +        /* We should already have an open ufd. Mark each memory
> > > +         * range as ufd.
> > > +         * Note: Do we need any madvises? Well it's not been accessed
> > > +         * yet, still probably need no THP to be safe, discard to be 
> > > safe?
> > > +         */
> > > +        struct uffdio_register reg_struct;
> > > +        reg_struct.range.start = (uintptr_t)dev_region->mmap_addr;
> > > +        reg_struct.range.len = dev_region->size + 
> > > dev_region->mmap_offset;
> > 
> > Do we really care the page faults between offset zero to mmap_offset?
> 
> No, but if we saw them we'd think it meant something had gone wrong,
> so it's good to trap them.

I'm fine with that, especially since that's now only used in the test
codes.  However that's a still bit confusing to me, especially if
current QEMU won't really handle that page fault (and it seems that
should never happen).  Maybe at least a comment would help on
explaining why we need to explicitly extend the range to listen, just
like below code when we do the mapping, though with a different
reason.

> 
> > I'm thinking whether we should add that mmap_offset into range.start
> > instead of range.len.
> > 
> > Also, I see that in current vu_set_mem_table_exec():
> > 
> >         /* We don't use offset argument of mmap() since the
> >          * mapped address has to be page aligned, and we use huge
> >          * pages.  */
> >         mmap_addr = mmap(0, dev_region->size + dev_region->mmap_offset,
> >                          PROT_READ | PROT_WRITE, MAP_SHARED,
> >                          vmsg->fds[i], 0);
> > 
> > So adding the mmap_offset will help to make sure we'll use huge pages?
> > Could it?  Or say, how could we be sure that size+mmap_offset would be
> > page aligned?
> 
> If you look into the set_mem_table_exec (non-postcopy) you'll see that
> code and comment comes from the non-postcopy version; but it's something
> which as you say we could probably simplify now.
> 
> The problem used to be, before we did the merging as part of this series
> (0026 vhost Huge page align and merge), we could end up with mappings
> being passed from the qemu that were for small ranges of memory that
> weren't aligned to a huge page boundary and thus the mmap would fail.
> With the merging code that's no longer true, so it means we
> could simplify as you say;  although this way it's a smaller change from
> the existing code.

I was thinking what if the memory section was e.g. splitted as below:

- range A: [0x0,      0x10):     non-RAM range, size     0x10
- range B: [0x10,     0x1ffff0):     RAM range, size 0x1fffe0
- range C: [0x1ffff0, 0x200000): non-RAM range, size     0x10

Ranges A+B+C will cover a 2M page while vhost-user master should only
send range B to the client. Then even size+mmap_offset (which is
0x1fffe0+0x10=0x1ffff0) shouldn't be aligned with the 2M boundary.
If previous mmap() can fail, would this fail too?

For sure this is a question not directly related to current code -
it's just something I'm not sure about.  So it is not a blocker of
current patch.  Thanks,

-- 
Peter Xu



reply via email to

[Prev in Thread] Current Thread [Next in Thread]