rule-list
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Rule-list] Re: no ppp support in install kernel?


From: Michael Fratoni
Subject: Re: [Rule-list] Re: no ppp support in install kernel?
Date: Sun, 19 May 2002 00:25:09 -0400
User-agent: KMail/1.4.1

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

On Saturday 18 May 2002 12:53 pm, Raymundo Baquirin wrote:

Hi Raymundo,

> I'm finally reunited with the serial cable and tried the setup with
> slattach again.  But no joy.  I can't ping either machine from the
> other.

I decided to try along with you. I grabbed an old abandoned laptop from 
work (Zeos 486, 8M of RAM, 80M hard drive, external floppy), and made a 
null modem cable.

> What I did:
>   On my desktop machine:
>     slattach -p slip -s 19200 /dev/ttyS1 &
>     ifconfig sl0 192.168.1.1 pointopoint 192.168.1.2 up
>     route add -host 192.168.1.2 sl0

I did about the same, but route add shouldn't be required.
The trick it turns out to have both machines connected, and running before 
you bring up the interface on either.

>   On the laptop:
>     insmod slhc.o                                      # load kernel
>     ./slattach -p slip -s 19200 /dev/ttyS0 &
>     ifconfig sl0 192.168.1.2 pointopoint 192.168.1.1 up

Snipped down to the commands I had to use. The only thing I found that 
needed to be changed is the ipconfig syntax. Busybox uses an older 
ifconfig, it seems.

The command on the laptop needs to be:
 ifconfig sl0 192.168.1.2 dstaddr 192.168.1.1

> I did notice in the slinky boot messages that the serial ports are
> called ttyS00 and ttyS01.  I tried making a ttyS00 device instead of
> ttyS0 but still got no ping.

I see the same thing in the logs on both machines. ttyS0 works for me, 
though.

Now, more detail. I got it working, and managed to nfs mount the rpms. 
However, it timed out everytime. Regardless of various nfs options, it 
times out just trying to get a directory listing of 
/mnt/cdrom/RedHat/RPMS. I can get as far as listing /mnt/cdrom/RedHat/, 
but even that is slow.
After a lot of wasted time, I gave up.

Then, I decided to try an HTTP install. Due to disk space problems on the 
laptop, I only allowed the installer to run through the copying of disk2, 
and doing the pivot root. Then I killed the installer, and ran the rpm 
commands manually so I could select only a bare minimum of packages.
It's installing slowly now. The downloading of glibc-common has taken over 
a half hour so far, and it's just half done. I believe I've done 5 or 6 
packages so far. :)

I'll let the install continue, but having seen the results, this isn't an 
install method I plan on supporting in any fashion. :) The slip network 
link is just too slow. If I rebuild the kernel and include cslip support, 
it might help, though I'm not sure of even that.

- -- 
- -Michael

pgp key:  http://www.tuxfan.homeip.net:8080/gpgkey.txt
Red Hat Linux 7.2 in 8M of RAM: http://www.rule-project.org/
- --
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.0.6 (GNU/Linux)
Comment: For info see http://www.gnupg.org

iEYEARECAAYFAjznKTAACgkQn/07WoAb/Su4fACeOTt4OKVtIyJfdmM1GOMaEj7b
4AIAnjyOh4FhpMUR7nCc+VE4epx1+O+4
=YMQK
-----END PGP SIGNATURE-----




reply via email to

[Prev in Thread] Current Thread [Next in Thread]