[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Bug-gmp] Re: SCO OpenServer and SCO UnixWare fix to config.guess an
From: |
Boyd Lynn Gerber |
Subject: |
Re: [Bug-gmp] Re: SCO OpenServer and SCO UnixWare fix to config.guess and make bug |
Date: |
Sat, 29 Jul 2000 22:53:56 -0600 (MDT) |
On 30 Jul 2000, Kevin Ryde wrote:
> If a fresh source tree doesn't work with "./configure --target=none",
> please make a bug report. (System details, compiler version, error
Compiler is gcc-2.95.2 on both systems. It does compile on OpenServer but
not on UnixWare.
----------------------------------------------------------------------------
Here is the detail on one of the UnixWare boxes.
----------------------------------------------------------------------------
Report about cpu for devsys0.zenez.com on Sat Jul 29 22:17:13 2000
There is one CPU on this system.
The speed of the CPU is approximately 233Mhz
0 on-line since 07/28/00 14:56:29
Report about memory for devsys0.zenez.com on Sat Jul 29 22:17:14 2000
Total Memory: 63.63 Mb
Usable Memory: 63.62 Mb
General Memory: 59.37 Mb
Dedicated Memory: 0 b
Report about ROM for devsys0.zenez.com on Sat Jul 29 22:17:14 2000
Adapter BIOS ROM
Address: 0xc0000 - 0xc7fff
Size: 32Kb
CheckSum: 0x00 (As expected)
Adapter BIOS ROM
Address: 0xc8000 - 0xc87ff
Size: 2Kb
CheckSum: 0x00 (As expected)
System BIOS ROM
Address: 0xe0000 - 0xfffff
Size: 128Kb
BIOS Date: 12/30/96
BIOS Category: IBM PC/XT-286
BIOS ID: Award SoftwareIBM COMPATIBLE 486 BIOS COPYRIGHT Award
Software Inc.oftware Inc. Aw oftw CAward Modular BIOS v4.51PG
Report about MP for devsys0.zenez.com on Sat Jul 29 22:17:14 2000
There is one CPU on this system.
Report about console for devsys0.zenez.com on Sat Jul 29 22:17:14 2000
Graphics card configuration
vt01, vt02, vt03, vt04, vt05, vt06, vt07, vt08, vt09,
vt10, vt11, vt12
Vendor: VESA
Model: ATI MACH64
Class: VBE (2.0)
Mode: 800x600 256-color
Visual: PseudoColor
Depth: 8
Width: 800
Height: 600
Mouse configuration
console, syscon, systty, vt00, vt01, vt02, vt03, vt04,
vt05, vt06, vt07, vt08
Driver: lt0_serial
Port: /dev/mouse
Report about ISA Plug-and-Play for devsys0.zenez.com on Sat Jul 29 22:17:14 2000
PnP Type: OS
Nodes: 0
NodeSize: 0
Report about PCI for devsys0.zenez.com on Sat Jul 29 22:17:14 2000
resmgr key = 16
vendor id = 0x8086=INTEL
device id = 0x7030
command register = 0x6=Memory Access Enable, Master Enable,
status register = 0x2200=Received Master Abort, DEVSEL# timing=medium
Revision ID = 0x2
Class Code = 0x60000=Bridge device - Host/PCI bridge
cache line size = 0x0
latency timer = 0x20
header type = 0x0
BIST = 0x0
Base Address 0 = 0x0
Base Address 1 = 0x0
Base Address 2 = 0x0
Base Address 3 = 0x0
Base Address 4 = 0x0
Base Address 5 = 0x0
CardBus CIS Pointer = 0x0
Subsystem Vendor ID = 0x0
Subsystem ID = 0x0
Expansion ROM Base Address = 0x0
Interrupt line = 0x0
Interrupt pin = 0x0
Min_Gnt = 0x0
Max_Lat = 0x0
resmgr key = 17
vendor id = 0x8086=INTEL
device id = 0x7000
command register = 0xf=I/O Access Enable, Memory Access Enable,
Master Enable, Special Cycle Recognition,
status register = 0x280=Fast Back-to-Back Capable, DEVSEL# timing=medium
Revision ID = 0x1
Class Code = 0x60100=Bridge device - PCI/ISA bridge
cache line size = 0x0
latency timer = 0x0
header type = 0xffffff80
BIST = 0x0
Base Address 0 = 0x0
Base Address 1 = 0x0
Base Address 2 = 0x0
Base Address 3 = 0x0
Base Address 4 = 0x0
Base Address 5 = 0x0
CardBus CIS Pointer = 0x0
Subsystem Vendor ID = 0x0
Subsystem ID = 0x0
Expansion ROM Base Address = 0x0
Interrupt line = 0x0
Interrupt pin = 0x0
Min_Gnt = 0x0
Max_Lat = 0x0
resmgr key = 18
vendor id = 0x8086=INTEL
device id = 0x7010
command register = 0x5=I/O Access Enable, Master Enable,
status register = 0x280=Fast Back-to-Back Capable, DEVSEL# timing=medium
Revision ID = 0x0
Class Code = 0x10180=Mass storage controller - IDE controller -
Master IDE device
cache line size = 0x0
latency timer = 0x20
header type = 0x0
BIST = 0x0
Base Address 0 = 0x0
Base Address 1 = 0x0
Base Address 2 = 0x0
Base Address 3 = 0x0
Base Address 4 = 0xf001
Base Address 5 = 0x0
CardBus CIS Pointer = 0x0
Subsystem Vendor ID = 0x0
Subsystem ID = 0x0
Expansion ROM Base Address = 0x0
Interrupt line = 0x0
Interrupt pin = 0x0
Min_Gnt = 0x0
Max_Lat = 0x0
resmgr key = 19
vendor id = 0xffff=unknown vendor
device id = 0xffff
command register = 0xffff=I/O Access Enable, Memory Access Enable,
Master Enable, Special Cycle Recognition, Memory Write & Invalidate Enable, VGA
Palette Snoop Enable, Parity Error Response, Wait Cycle Enable, System Error
Enable, Fast Back-to-Back Enable,
status register = 0xffff=66MHz-capable, UDF Supported, Fast Back-to-Back
Capable, Data Parity Reported, Signaled Target Abort, Received Target Abort,
Received Master Abort, Signaled System Error, Detected Parity Error, DEVSEL#
timing=reserved(0x600)
Revision ID = 0xff
Class Code = 0xffffff=device does not fit any of the defined classed
codes
cache line size = 0xffffffff
latency timer = 0xffffffff
header type = 0xffffffff
BIST = 0xffffffff
Base Address 0 = 0xffffffff
Base Address 1 = 0xffffffff
Base Address 2 = 0xffffffff
Base Address 3 = 0xffffffff
Base Address 4 = 0xffffffff
Base Address 5 = 0xffffffff
CardBus CIS Pointer = 0xffffffff
Subsystem Vendor ID = 0xffff
Subsystem ID = 0xffff
Expansion ROM Base Address = 0xffffffff
Interrupt line = 0xff
Interrupt pin = 0xff
Min_Gnt = 0xff
Max_Lat = 0xff
resmgr key = 20
vendor id = 0x10b7=3COM CORPORATION
device id = 0x5900
command register = 0x7=I/O Access Enable, Memory Access Enable,
Master Enable,
status register = 0x200=DEVSEL# timing=medium
Revision ID = 0x0
Class Code = 0x20000=Network controller - Ethernet controller
cache line size = 0x0
latency timer = 0xfffffff0
header type = 0x0
BIST = 0x0
Base Address 0 = 0x6401
Base Address 1 = 0x0
Base Address 2 = 0x0
Base Address 3 = 0x0
Base Address 4 = 0x0
Base Address 5 = 0x0
CardBus CIS Pointer = 0x0
Subsystem Vendor ID = 0x0
Subsystem ID = 0x0
Expansion ROM Base Address = 0x0
Interrupt line = 0xb
Interrupt pin = 0x1
Min_Gnt = 0x3
Max_Lat = 0x8
resmgr key = 21
vendor id = 0x9004=ADAPTEC
device id = 0x6178
command register = 0x7=I/O Access Enable, Memory Access Enable,
Master Enable,
status register = 0x280=Fast Back-to-Back Capable, DEVSEL# timing=medium
Revision ID = 0x1
Class Code = 0x10000=Mass storage controller - SCSI controller
cache line size = 0x8
latency timer = 0x20
header type = 0x0
BIST = 0x0
Base Address 0 = 0x6001
Base Address 1 = 0xe1000000
Base Address 2 = 0x0
Base Address 3 = 0x0
Base Address 4 = 0x0
Base Address 5 = 0x0
CardBus CIS Pointer = 0x0
Subsystem Vendor ID = 0x0
Subsystem ID = 0x0
Expansion ROM Base Address = 0x0
Interrupt line = 0xa
Interrupt pin = 0x1
Min_Gnt = 0x4
Max_Lat = 0x4
resmgr key = 22
vendor id = 0x1002=ATI TECHNOLOGIES INC
device id = 0x4755
command register = 0x83=I/O Access Enable, Memory Access Enable,
Wait Cycle Enable,
status register = 0x280=Fast Back-to-Back Capable, DEVSEL# timing=medium
Revision ID = 0x9a
Class Code = 0x30000=Display controller - VGA compatible controller
cache line size = 0x8
latency timer = 0x20
header type = 0x0
BIST = 0x0
Base Address 0 = 0xe0000000
Base Address 1 = 0x6601
Base Address 2 = 0xe1001000
Base Address 3 = 0x0
Base Address 4 = 0x0
Base Address 5 = 0x0
CardBus CIS Pointer = 0x0
Subsystem Vendor ID = 0x1002
Subsystem ID = 0x4755
Expansion ROM Base Address = 0x0
Interrupt line = 0xff
Interrupt pin = 0x0
Min_Gnt = 0x8
Max_Lat = 0x0
16 DEVNUM 0 0 0 0
17 DEVNUM 0 7 7 0 ?
18 DEVNUM 0 7 7 0 ?
19 DEVNUM 0 7 7 0 ?
20 DEVNUM 0 17 11 0 ?
21 DEVNUM 0 18 12 0 ?
22 DEVNUM 0 20 14 0 ?
Report about cfg for devsys0.zenez.com on Sat Jul 29 22:17:15 2000
architecture=IA32
bus_types=PCI2.10,ISA,PnP1.0
hostname=devsys0.zenez.com
hw_provider=Generic AT
hw_serial=2GE032573
kernel_stamp=99/05/06
machine=AMD-K6
num_cg=1
num_cpu=1
os_base=UNIX_SVR5
os_provider=SCO
release=5
srpc_domain=
sysname=UnixWare
user_limit=6
version=7.1.0
-----------------------------------------------------------------------------
> messages, offending line, suspected cause, etc.) It's possible you're
> the first person to try GMP on SCO.
gcc -E -DHAVE_CONFIG_H -I. -I. -I.. -I.. -DOPERATION_add_n -g -O2 -DPIC
add_n
.S | grep -v '^#' >tmp-add_n.s
add_n.S:32: asm-syntax.h: No such file or directory
/bin/sh ../libtool --mode=compile gcc -c -DHAVE_CONFIG_H
-I. -I. -I.. -I.. -DOPE
RATION_add_n -g -O2 tmp-add_n.s -o add_n.lo
gcc -c -DHAVE_CONFIG_H -I. -I. -I.. -I.. -DOPERATION_add_n -g -O2
tmp-add_n.s -o
add_n.o
UX:as: ERROR: tmp-add_n.s:35:syntax error at integer constant: 3
UX:as: ERROR: tmp-add_n.s:36:syntax error at (
UX:as: ERROR: tmp-add_n.s:37:expecting name operand for .globl, operand 1
UX:as: ERROR: tmp-add_n.s:38:syntax error at :
UX:as: ERROR: tmp-add_n.s:67:syntax error at (
UX:as: ERROR: tmp-add_n.s:70:syntax error at integer constant: 3
UX:as: ERROR: tmp-add_n.s:71:syntax error at (
UX:as: ERROR: tmp-add_n.s:72:expecting name operand for .globl, operand 1
UX:as: ERROR: tmp-add_n.s:73:syntax error at :
UX:as: ERROR: tmp-add_n.s:94:syntax error at integer constant: 3
UX:as: ERROR: tmp-add_n.s:168:syntax error at (
make[2]: *** [add_n.lo] Error 1
make[2]: Leaving directory `/usr/zenez/build/uw7/gmp-3.0.1/mpn'
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory `/usr/zenez/build/uw7/gmp-3.0.1'
make: *** [all-recursive-am] Error 2
--
Boyd Gerber <address@hidden>
ZENEZ 3748 Valley Forge Road, Magna Utah 84044
Office 801-250-0795 FAX 801-250-7975