[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: parted and 78 heads
|
From: |
Mario Gzuk |
|
Subject: |
Re: parted and 78 heads |
|
Date: |
Tue, 03 Oct 2006 15:46:56 +0200 |
Hi,
nobody out there who has simular problems?
Here some more informations:
parted version: 1.7.1
If I load the edd module (BIOS Enhanced Disk Drive calls determine boot
disk) the edd module tells me (if the disk is empty): 255 heads and 63
sektors/track after creating partitions with parted the edd module tells
me 78 heads and 60 sektors/track....
The effect is not if I create the partitions with fdsik....
greetings mario
Am Freitag, den 29.09.2006, 14:56 +0200 schrieb Mario Gzuk:
> Hi,
> we have the following problem:
> parted say that the disk (see below) has BIOS cylinder,head,sector
> geometry: 9729,255,63.
> But it writes other informations into the first sector of the fat
> partition...
> In sektor 1 of the fat32 partition the 2 bytes with offset 26 should
> show the number of heads for interupt 0x13. And IMHO that should be the
> same as parted gets from the BIOS.... Or am i wrong? But at these 2
> bytes there is a value of "78" instead of "255". And also the 2 bytes
> with offset 24 (which should contain the sectors per track for interupt
> 0x13) shows 60 instead of 63.
> These all leads to the result of a "ntldr not found" problem.....
>
> Maybe you can help me out of this ????
>
> Here follows the system informations, if you need more let me know.
>
> _____________SYSTEM INFORMATIONS_______________________________________
>
> here is the output from "parted /dev/dsk print unit s print unit chs
> print"
>
> #parted start
> Disk /dev/sda: 80.0GB
> Sector size (logical/physical): 512B/512B
> Partition Table: msdos
>
> Number Start End Size Type File system Flags
> 1 0.51kB 4000MB 4000MB primary fat32 boot, lba
>
>
> Disk /dev/sda: 156301487s
> Sector size (logical/physical): 512B/512B
> Partition Table: msdos
>
> Number Start End Size Type File system Flags
> 1 1s 7812500s 7812500s primary fat32 boot, lba
>
>
> Disk /dev/sda: 9729,80,62
> Sector size (logical/physical): 512B/512B
> BIOS cylinder,head,sector geometry: 9729,255,63. Each cylinder is
> 8225kB.
> Partition Table: msdos
>
> Number Start End Type File system Flags
> 1 0,0,1 486,77,59 primary fat32 boot, lba
> ### parted end
>
>
> Here are some additional informations about the system
>
>
> ###dmesg start
> BIOS-e820: 000000001ffd0000 - 0000000020000000 (ACPI NVS)
> BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
> BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
> BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
> 0MB HIGHMEM available.
> 511MB LOWMEM available.
> On node 0 totalpages: 131008
> DMA zone: 4096 pages, LIFO batch:0
> Normal zone: 126912 pages, LIFO batch:31
> DMI 2.3 present.
> ACPI: RSDP (v000 ACPIAM ) @
> 0x000f9ed0
> ACPI: RSDT (v001 A M I OEMRSDT 0x02000616 MSFT 0x00000097) @
> 0x1ffc0000
> ACPI: FADT (v002 A M I OEMFACP 0x02000616 MSFT 0x00000097) @
> 0x1ffc0200
> ACPI: MADT (v001 A M I OEMAPIC 0x02000616 MSFT 0x00000097) @
> 0x1ffc0390
> ACPI: OEMB (v001 A M I OEMBIOS 0x02000616 MSFT 0x00000097) @
> 0x1ffd0040
> ACPI: DSDT (v001 A0128 A0128003 0x00000003 INTL 0x02002026) @
> 0x00000000
> ACPI: PM-Timer IO Port: 0x4008
> Allocating PCI resources starting at 30000000 (gap:
> 20000000:dec00000)
> Built 1 zonelists
> Enabling fast FPU save and restore... done.
> Enabling unmasked SIMD FPU exception support... done.
> Initializing CPU#0
> PID hash table entries: 2048 (order: 11, 8192 bytes)
> Detected 1808.896 MHz processor.
> Using pmtmr for high-res timesource
> Console: colour VGA+ 80x25
> Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
> Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
> Memory: 491936k/524032k available (3565k kernel code, 31592k
> reserved, 1735k data, 324k init, 0k highmem)
> Checking if this processor honours the WP bit even in supervisor
> mode... Ok.
> Calibrating delay using timer specific routine.. 3620.14
> BogoMIPS (lpj=1810070)
> Security Framework v1.0.0 initialized
> Capability LSM initialized
> Mount-cache hash table entries: 512
> CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000
> 00000000 00000001 00000000 00000001
> CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000
> 00000000 00000001 00000000 00000001
> CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
> bytes/line)
> CPU: L2 Cache: 256K (64 bytes/line)
> CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410
> 00000001 00000000 00000001
> Intel machine check architecture supported.
> Intel machine check reporting enabled on CPU#0.
> CPU: AMD Sempron(tm) Processor 3100+ stepping 02
> Checking 'hlt' instruction... OK.
> SMP alternatives: switching to UP code
> Freeing SMP alternatives: 0k freed
> ACPI: setting ELCR to 0200 (from 0e88)
> checking if image is initramfs... it is
> Freeing initrd memory: 20974k freed
> NET: Registered protocol family 16
> ACPI: bus type pci registered
> PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
> Setting up standard PCI resources
> ACPI: Subsystem revision 20060127
> ACPI: Interpreter enabled
> ACPI: Using PIC for interrupt routing
> ACPI: PCI Root Bridge [PCI0] (0000:00)
> PCI: Probing PCI hardware (bus 00)
> Boot video device is 0000:01:00.0
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
> ACPI: Power Resource [ISAV] (on)
> ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *11 12 14 15)
> ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15)
> ACPI: PCI Interrupt Link [LUS0] (IRQs *3 4 5 7 9 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LUS1] (IRQs 3 4 5 7 *9 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LUS2] (IRQs 3 4 5 7 9 *10 11 12 14 15)
> ACPI: PCI Interrupt Link [LKLN] (IRQs 3 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> ACPI: PCI Interrupt Link [LAUI] (IRQs 3 4 5 *7 9 10 11 12 14 15)
> ACPI: PCI Interrupt Link [LKMO] (IRQs 3 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 7 9 10 11 12 14 15)
> *0, disabled.
> ACPI: PCI Interrupt Link [LTID] (IRQs 10) *0
> ACPI: PCI Interrupt Link [LTIE] (IRQs 10) *0, disabled.
> ACPI: PCI Interrupt Link [LATA] (IRQs 3 4 6 7 10 11 12 *14 15)
> Linux Plug and Play Support v0.97 (c) Adam Belay
> pnp: PnP ACPI init
> pnp: PnP ACPI: found 15 devices
> SCSI subsystem initialized
> usbcore: registered new driver usbfs
> usbcore: registered new driver hub
> PCI: Using ACPI for IRQ routing
> PCI: If a device doesn't work, try "pci=routeirq". If it helps,
> post a report
> pnp: 00:0b: ioport range 0x480-0x487 has been reserved
> pnp: 00:0b: ioport range 0xd00-0xd07 has been reserved
> PCI: Bridge: 0000:00:0b.0
> IO window: disabled.
> MEM window: fd900000-fe9fffff
> PREFETCH window: e9800000-ed7fffff
> PCI: Bridge: 0000:00:0e.0
> IO window: c000-cfff
> MEM window: fea00000-feafffff
> PREFETCH window: disabled.
> PCI: Setting latency timer of device 0000:00:0e.0 to 64
> NET: Registered protocol family 2
> IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
> TCP established hash table entries: 16384 (order: 4, 65536
> bytes)
> TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
> TCP: Hash tables configured (established 16384 bind 8192)
> TCP reno registered
> apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
> Total HugeTLB memory allocated, 0
> NTFS driver 2.1.27 [Flags: R/O].
> Initializing Cryptographic API
> io scheduler noop registered
> io scheduler anticipatory registered
> io scheduler deadline registered
> io scheduler cfq registered (default)
> Real Time Clock Driver v1.12ac
> Linux agpgart interface v0.101 (c) Dave Jones
> agpgart: Detected AGP bridge 0
> agpgart: Setting up Nforce3 AGP.
> agpgart: AGP aperture is 128M @ 0xf0000000
> ACPI: Power Button (FF) [PWRF]
> ACPI: Power Button (CM) [PWRB]
> ibm_acpi: ec object not found
> Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
> disabled
> serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> 00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64
> irq 1,12
> serio: i8042 AUX port at 0x60,0x64 irq 12
> serio: i8042 KBD port at 0x60,0x64 irq 1
> mice: PS/2 mouse device common for all mice
> input: PC Speaker as /class/input/input0
> input: AT Translated Set 2 keyboard as /class/input/input1
> input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
> RAMDISK driver initialized: 16 RAM disks of 4096K size 1024
> blocksize
> loop: loaded (max 8 devices)
> nbd: registered device at major 43
> Intel(R) PRO/1000 Network Driver - version 7.0.33-k2
> Copyright (c) 1999-2005 Intel Corporation.
> Intel(R) PRO/10GbE Network Driver - version 1.0.100-k2
> Copyright (c) 1999-2005 Intel Corporation.
> dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $
> FW=Build 550 11/16/96 03:45:15
> FW Version=$Version$
> pcnet32.c:v1.32 18.Mar.2006 address@hidden
> e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
> e100: Copyright(c) 1999-2005 Intel Corporation
> ThunderLAN driver v1.15
> TLAN: 0 devices installed, PCI: 0 EISA: 0
> ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
> forcedeth.c: Reverse Engineered nForce ethernet driver. Version
> 0.54.
> tun: Universal TUN/TAP device driver, 1.6
> tun: (C) 1999-2004 Max Krasnyansky <address@hidden>
> ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
> ipw2100: Copyright(c) 2003-2006 Intel Corporation
> ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver,
> git-1.1.1
> ipw2200: Copyright(c) 2003-2006 Intel Corporation
> STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
> orinoco 0.15rc3 (David Gibson <address@hidden>,
> Pavel Roskin <address@hidden>, et al)
> orinoco_cs 0.15rc3 (David Gibson <address@hidden>,
> Pavel Roskin <address@hidden>, et al)
> orinoco_plx 0.15rc3 (Pavel Roskin <address@hidden>, David Gibson
> <address@hidden>, Daniel Barlow <address@hidden>)
> orinoco_pci 0.15rc3 (Pavel Roskin <address@hidden>, David Gibson
> <address@hidden> & Jean Tourrilhes
> <address@hidden>)
> orinoco_tmd 0.15rc3 (Joerg Dorchain <address@hidden>)
> orinoco_nortel 0.15rc3 (Tobias Hoffmann & Christoph Jungegger
> <address@hidden>)
> spectrum_cs 0.15rc3 (Pavel Roskin <address@hidden>, David Gibson
> <address@hidden>, et al)
> airo(): Probing for PCI adapters
> airo(): Finished probing for PCI adapters
> Loaded prism54 driver, version 1.2
> hostap_cs: 0.4.4-kernel (Jouni Malinen <address@hidden>)
> hostap_plx: 0.4.4-kernel (Jouni Malinen <address@hidden>)
> hostap_pci: 0.4.4-kernel (Jouni Malinen <address@hidden>)
> dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
> winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker
> <address@hidden>
> http://www.scyld.com/network/drivers.html
> Linux Tulip driver version 1.1.13 (May 11, 2002)
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
> PCI: setting IRQ 11 as level-triggered
> ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKC] -> GSI 11
> (level, low) -> IRQ 11
> tulip0: EEPROM default media type Autosense.
> tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY
> (3) block.
> tulip0: MII transceiver #17 config 1000 status 782d advertising
> 01e1.
> eth0: Digital DS21143 Tulip rev 65 at 0001cc00,
> 00:00:CB:53:4C:5C, IRQ 11.
> uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
> libata version 1.20 loaded.
> ieee1394: Initialized config rom entry `ip1394'
> ieee1394: raw1394: /dev/raw1394 device initialized
> usbmon: debugfs is not available
> usbcore: registered new driver libusual
> usbcore: registered new driver usbhid
> drivers/usb/input/hid-core.c: v2.6:USB HID core driver
> usbcore: registered new driver usblcd
> usbcore: registered new driver usbled
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 10
> IPv6 over IPv4 tunneling driver
> NET: Registered protocol family 17
> ieee80211: 802.11 data/management/control stack, git-1.1.7
> ieee80211: Copyright (C) 2004-2005 Intel Corporation
> <address@hidden>
> ieee80211_crypt: registered algorithm 'NULL'
> ieee80211_crypt: registered algorithm 'WEP'
> ieee80211_crypt: registered algorithm 'CCMP'
> ieee80211_crypt: registered algorithm 'TKIP'
> Using IPI Shortcut mode
> ACPI wakeup devices:
> PS2K PS2M UAR1 USB0 MAC USB1 USB2 P0P1
> ACPI: (supports S0 S1 S3 S4 S5)
> drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
> Freeing unused kernel memory: 324k freed
> 3ware 9000 Storage Controller device driver for Linux
> v2.26.02.007.
> 3ware Storage Controller device driver for Linux v1.26.02.001.
> Loading Adaptec I2O RAID: Version 2.4 Build 5go
> Detecting Adaptec I2O RAID controllers...
> scsi: <fdomain> Detection failed (no card)
> GDT-HA: Storage RAID Controller Driver. Version: 3.04
> GDT-HA: Found 0 PCI Storage RAID Controllers
> Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
> ide: Assuming 33MHz system bus speed for PIO modes; override
> with idebus=xx
> ipr: IBM Power RAID SCSI Device Driver version: 2.1.3 (March 29,
> 2006)
> iscsi: registered transport (tcp)
> nsp32: loading...
> sata_nv 0000:00:0a.0: version 0.8
> ACPI: PCI Interrupt Link [LTID] BIOS reported IRQ 0, using IRQ
> 10
> ACPI: PCI Interrupt Link [LTID] enabled at IRQ 10
> PCI: setting IRQ 10 as level-triggered
> ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LTID] -> GSI 10
> (level, low) -> IRQ 10
> PCI: Setting latency timer of device 0000:00:0a.0 to 64
> ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD000 irq 10
> ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD008 irq 10
> ata1: SATA link up 1.5 Gbps (SStatus 113)
> ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01
> 87:4023 88:407f
> ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48
> nv_sata: Primary device added
> nv_sata: Primary device removed
> nv_sata: Secondary device removed
> ata1: dev 0 configured for UDMA/133
> scsi0 : sata_nv
> ata2: SATA link down (SStatus 0)
> scsi1 : sata_nv
> Vendor: ATA Model: ST3808110AS Rev: 3.AA
> Type: Direct-Access ANSI SCSI revision:
> 05
> SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
> sda: Write Protect is off
> sda: Mode Sense: 00 3a 00 00
> SCSI device sda: drive cache: write back
> sda: sda1
> sd 0:0:0:0: Attached scsi disk sda
> sd 0:0:0:0: Attached scsi generic sg0 type 0
> Adaptec aacraid driver (1.1-5[2409]-mh1)
> Emulex LightPulse Fibre Channel SCSI driver 8.1.6
> Copyright(c) 2004-2006 Emulex. All rights reserved.
> megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST
> 2005)
> megaraid: 2.20.4.8 (Release Date: Mon Apr 11 12:27:22 EST 2006)
> megasas: 00.00.02.04 Fri Feb 03 14:31:44 PST 2006
> nsp_cs: loading...
> QLogic Fibre Channel HBA Driver
> Probing IDE interface ide0...
> hda: TOSHIBA DVD-ROM SD-M1912, ATAPI CD/DVD-ROM drive
> Probing IDE interface ide1...
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide-scsi is deprecated for cd burning! Use ide-cd and give
> dev=/dev/hdX as device
> scsi2 : SCSI host adapter emulation for IDE ATAPI devices
> Vendor: TOSHIBA Model: DVD-ROM SD-M1912 Rev: TM01
> Type: CD-ROM ANSI SCSI revision:
> 00
> sr0: scsi-1 drive
> Uniform CD-ROM driver Revision: 3.20
> sr 2:0:0:0: Attached scsi CD-ROM sr0
> sr 2:0:0:0: Attached scsi generic sg1 type 5
> NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
> NFORCE3-250: chipset revision 162
> NFORCE3-250: not 100% native mode: will probe irqs later
> NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
> NFORCE3-250: port 0x01f0 already claimed by ide0
> ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio,
> hdd:pio
> Probing IDE interface ide1...
> ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 10
> ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 10
> (level, low) -> IRQ 10
> PCI: Setting latency timer of device 0000:00:02.2 to 64
> ehci_hcd 0000:00:02.2: EHCI Host Controller
> ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus
> number 1
> ehci_hcd 0000:00:02.2: debug port 1
> PCI: cache line size of 64 is not supported by device
> 0000:00:02.2
> ehci_hcd 0000:00:02.2: irq 10, io mem 0xfebffc00
> ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec
> 2004
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 8 ports detected
> ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI)
> Driver (PCI)
> ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 3
> PCI: setting IRQ 3 as level-triggered
> ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 3
> (level, low) -> IRQ 3
> PCI: Setting latency timer of device 0000:00:02.0 to 64
> ohci_hcd 0000:00:02.0: OHCI Host Controller
> ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus
> number 2
> ohci_hcd 0000:00:02.0: irq 3, io mem 0xfebfd000
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 4 ports detected
> ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 9
> PCI: setting IRQ 9 as level-triggered
> ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 9
> (level, low) -> IRQ 9
> PCI: Setting latency timer of device 0000:00:02.1 to 64
> ohci_hcd 0000:00:02.1: OHCI Host Controller
> ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus
> number 3
> ohci_hcd 0000:00:02.1: irq 9, io mem 0xfebfe000
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 4 ports detected
> USB Universal Host Controller Interface driver v3.0
> BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
> eth0: Setting full-duplex based on MII#17 link partner
> capability of 45e1.
> eth0: no IPv6 routers present
> ###dmesg end
>
>
> ###lspci start
> 00:00.0 0600: 10de:00e1 (rev a1)
> 00:01.0 0601: 10de:00e0 (rev a2)
> 00:01.1 0c05: 10de:00e4 (rev a1)
> 00:02.0 0c03: 10de:00e7 (rev a1)
> 00:02.1 0c03: 10de:00e7 (rev a1)
> 00:02.2 0c03: 10de:00e8 (rev a2)
> 00:06.0 0401: 10de:00ea (rev a1)
> 00:08.0 0101: 10de:00e5 (rev a2)
> 00:0a.0 0101: 10de:00e3 (rev a2)
> 00:0b.0 0604: 10de:00e2 (rev a2)
> 00:0e.0 0604: 10de:00ed (rev a2)
> 00:18.0 0600: 1022:1100
> 00:18.1 0600: 1022:1101
> 00:18.2 0600: 1022:1102
> 00:18.3 0600: 1022:1103
> 01:00.0 0300: 102b:0525 (rev 85)
> 02:08.0 0200: 1011:0019 (rev 41)
>
> 00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host
> Bridge (rev a1)
> Subsystem: ASUSTeK Computer Inc. Unknown device 813f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
> Region 0: Memory at f0000000 (32-bit, prefetchable)
> [size=128M]
> Capabilities: [44] HyperTransport: Slave or Primary
> Interface
> Command: BaseUnitID=0 UnitCnt=14 MastHost-
> DefDir- DUL-
> Link Control 0: CFlE+ CST- CFE- <LkFail- Init+
> EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit
> DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
> Link Control 1: CFlE- CST- CFE- <LkFail+ Init-
> EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
> Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit
> DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
> Revision ID: 1.03
> Link Frequency 0: 800MHz
> Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 0: 200MHz+ 300MHz+
> 400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz-
> Vend-
> Feature Capability: IsocFC+ LDTSTOP+ CRCTM-
> ECTLT- 64bA- UIDRD-
> Link Frequency 1: 200MHz
> Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
> Link Frequency Capability 1: 200MHz- 300MHz-
> 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz-
> Vend-
> Error Handling: PFlE- OFlE- PFE- OFE- EOCFE-
> RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE-
> SERRNFE-
> Prefetchable memory behind bridge Upper: 00-00
> Bus Number: 00
> Capabilities: [c0] AGP version 2.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh-
> GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
> Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64-
> 64bit- FW- Rate=x1
>
> 00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge
> (rev a2)
> Subsystem: ASUSTeK Computer Inc. Unknown device 813f
> Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System
> Management (rev a1)
> Subsystem: ASUSTeK Computer Inc. Unknown device 813f
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 0
> Region 0: I/O ports at 5080 [size=32]
> Region 4: I/O ports at 5000 [size=64]
> Region 5: I/O ports at 5040 [size=64]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:02.0 USB Controller: nVidia Corporation CK8S USB Controller
> (rev a1) (prog-if 10 [OHCI])
> Subsystem: ASUSTeK Computer Inc. Unknown device 813f
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin A routed to IRQ 3
> Region 0: Memory at febfd000 (32-bit, non-prefetchable)
> [size=4K]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:02.1 USB Controller: nVidia Corporation CK8S USB Controller
> (rev a1) (prog-if 10 [OHCI])
> Subsystem: ASUSTeK Computer Inc. Unknown device 813f
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin B routed to IRQ 9
> Region 0: Memory at febfe000 (32-bit, non-prefetchable)
> [size=4K]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0
> Controller (rev a2) (prog-if 20 [EHCI])
> Subsystem: ASUSTeK Computer Inc. Unknown device 813f
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin C routed to IRQ 10
> Region 0: Memory at febffc00 (32-bit, non-prefetchable)
> [size=256]
> Capabilities: [44] Debug port
> Capabilities: [80] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0+,D1+,D2+,D3hot+,D3cold+)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:06.0 Multimedia audio controller: nVidia Corporation nForce3
> 250Gb AC'97 Audio Controller (rev a1)
> Subsystem: ASUSTeK Computer Inc. Unknown device 812a
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (500ns min, 1250ns max)
> Interrupt: pin A routed to IRQ 7
> Region 0: I/O ports at e800 [size=256]
> Region 1: I/O ports at ec00 [size=128]
> Region 2: Memory at febfb000 (32-bit, non-prefetchable)
> [size=4K]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA
> Controller (v2.5) (rev a2) (prog-if 8a [Master SecP PriP])
> Subsystem: ASUSTeK Computer Inc. Unknown device 813f
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (750ns min, 250ns max)
> Region 4: I/O ports at ffa0 [size=16]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA
> Controller (v2.5) (rev a2) (prog-if 85 [Master SecO PriO])
> Subsystem: ASUSTeK Computer Inc. Unknown device 813f
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0 (750ns min, 250ns max)
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at 09f0 [size=8]
> Region 1: I/O ports at 0bf0 [size=4]
> Region 2: I/O ports at 0970 [size=8]
> Region 3: I/O ports at 0b70 [size=4]
> Region 4: I/O ports at d000 [size=16]
> Region 5: I/O ports at dc00 [size=128]
> Capabilities: [44] Power Management version 2
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>
> 00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to
> PCI Bridge (rev a2) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 16
> Bus: primary=00, secondary=01, subordinate=01,
> sec-latency=10
> I/O behind bridge: 0000f000-00000fff
> Memory behind bridge: fd900000-fe9fffff
> Prefetchable memory behind bridge: e9800000-ed7fffff
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset-
> FastB2B-
>
> 00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI
> Bridge (rev a2) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR+ <PERR-
> Latency: 0
> Bus: primary=00, secondary=02, subordinate=02,
> sec-latency=128
> I/O behind bridge: 0000c000-0000cfff
> Memory behind bridge: fea00000-feafffff
> Prefetchable memory behind bridge: fff00000-000fffff
> Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
> BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset-
> FastB2B-
>
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8
> [Athlon64/Opteron] HyperTransport Technology Configuration
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Capabilities: [80] HyperTransport: Host or Secondary
> Interface
> !!! Possibly incomplete decoding
> Command: WarmRst+ DblEnd-
> Link Control: CFlE- CST- CFE- <LkFail- Init+
> EOC- TXO- <CRCErr=0
> Link Config: MLWI=16bit MLWO=16bit LWI=16bit
> LWO=16bit
> Revision ID: 1.02
>
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8
> [Athlon64/Opteron] Address Map
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8
> [Athlon64/Opteron] DRAM Controller
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8
> [Athlon64/Opteron] Miscellaneous Control
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
>
> 01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA
> G400/G450 (rev 85) (prog-if 00 [VGA])
> Subsystem: Matrox Graphics, Inc. Millennium G450 32Mb
> SDRAM Dual Head
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
> VGASnoop- ParErr- Stepping- SERR- FastB2B-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (4000ns min, 8000ns max), Cache Line Size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at ea000000 (32-bit, prefetchable)
> [size=32M]
> Region 1: Memory at fe9fc000 (32-bit, non-prefetchable)
> [size=16K]
> Region 2: Memory at fe000000 (32-bit, non-prefetchable)
> [size=8M]
> Expansion ROM at fe9c0000 [disabled] [size=128K]
> Capabilities: [dc] Power Management version 2
> Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Capabilities: [f0] AGP version 2.0
> Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh-
> GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
> Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64-
> 64bit- FW- Rate=x1
>
> 02:08.0 Ethernet controller: Digital Equipment Corporation
> DECchip 21142/43 (rev 41)
> Subsystem: Compu-Shack Unknown device 4235
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+
> VGASnoop- ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
> >TAbort- <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64 (5000ns min, 10000ns max), Cache Line Size
> 08
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at cc00 [size=128]
> Region 1: Memory at feaffc00 (32-bit, non-prefetchable)
> [size=1K]
> Expansion ROM at fea80000 [disabled] [size=256K]
>
> ###lspci end
>
>
> ###fdisk start
>
> Disk /dev/sda: 80.0 GB, 80026361856 bytes
> 255 heads, 63 sectors/track, 9729 cylinders
> Units = cylinders of 16065 * 512 = 8225280 bytes
>
> ###fdsik end
>
>
>
>
> ###memeinfo start
> MemTotal: 513352 kB
> MemFree: 434436 kB
> Buffers: 0 kB
> Cached: 64844 kB
> SwapCached: 0 kB
> Active: 18068 kB
> Inactive: 49084 kB
> HighTotal: 0 kB
> HighFree: 0 kB
> LowTotal: 513352 kB
> LowFree: 434436 kB
> SwapTotal: 0 kB
> SwapFree: 0 kB
> Dirty: 0 kB
> Writeback: 0 kB
> Mapped: 3988 kB
> Slab: 8128 kB
> CommitLimit: 256676 kB
> Committed_AS: 4452 kB
> PageTables: 120 kB
> VmallocTotal: 507896 kB
> VmallocUsed: 3068 kB
> VmallocChunk: 504636 kB
> HugePages_Total: 0
> HugePages_Free: 0
> HugePages_Rsvd: 0
> Hugepagesize: 4096 kB
> ###meminfo end
>
>
> ###cpuinfo start
> processor : 0
> vendor_id : AuthenticAMD
> cpu family : 15
> model : 44
> model name : AMD Sempron(tm) Processor 3100+
> stepping : 2
> cpu MHz : 1808.896
> cache size : 256 KB
> fdiv_bug : no
> hlt_bug : no
> f00f_bug : no
> coma_bug : no
> fpu : yes
> fpu_exception : yes
> cpuid level : 1
> wp : yes
> flags : fpu vme de pse tsc msr pae mce cx8 apic sep
> mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx
> mmxext fxsr_opt lm 3dnowext 3dnow up pni lahf_lm ts fid vid ttp
> tm stc
> bogomips : 3620.14
>
> ###cpuinfo end
>
> greetings mario gzuk
>
>
>
> _______________________________________________
> bug-parted mailing list
> address@hidden
> http://lists.gnu.org/mailman/listinfo/bug-parted
- Re: parted and 78 heads,
Mario Gzuk <=