RE: [Ltib] Build failed

[Stuart Hughes]

Hi Dharmesh,

You don't need to remove ltib, just the failed build of lkc.  Can you do
this:

$ rm -rf /opt/freescale/ltib/usr/src/rpm/BUILD/lkc-1.4
$ ./ltib

If that fails, can you send me the host_config.log.  This should show me
what actually happened to cause the build of lkc to fail.

Regards, Stuart


On Fri, 2006-11-24 at 11:48 +0530, Dharmesh wrote:
> Hi Stuart,
> 
> I am using MPC832xE_MDS_20060829-LTIB.iso image which I downloaded from
> freescale website. 
> 
> Before receive your mail I follow this procedure and I founded these
> results.
> 
> 1. removed ltib folder 
> 2. install again ltib 
> 3. $./ltib 
> 
> host_config.log file is appearing same as I attached in previous mail.
> 
> It can not create opt folder also in ltib directory.
> 
> After that I have removed build configuration of lkc from config file which
> is in /config/platform/host/ltib.preconfig.
> 
> After that it was compile successfully without lkc.
> 
> While executing command
> $./ltib -c            
> gives me error like this.
> 
> +'['-n '' ']'
> +'['-n '' ']'
> + cd config/platform/mpc832xemds
> + mconf main.lkc
> Sh:line10: mconf: command not found
> Died at ./ltib line 2464
> 
> Regards,
> Dharmesh Desai
> 
> -----Original Message-----
> From: Stuart Hughes [mailto:address@hidden 
> Sent: Thursday, November 23, 2006 4:28 PM
> To: Dharmesh
> Cc: address@hidden
> Subject: Re: [Ltib] Build failed
> 
> Hi Dharmesh,
> 
> You don't need to remove ltib, just the failed build of lkc.  Can you do
> this:
> 
> $ rm -rf /opt/freescale/ltib/usr/src/rpm/BUILD/lkc-1.4
> $ ./ltib
> 
> If that fails, can you send me the host_config.log.  This should show me
> what actually happened to cause the build of lkc to fail.
> 
> Can you tell me which version of ltib you have, it looks like you must be
> using an iso image?  Can you tell me the name of the iso.  This will help me
> track down if there have been any updated in this area.
> 
> Regards, Stuart
> 
> On Thu, 2006-11-23 at 11:50 +0530, Dharmesh wrote:
> > Hi Stuart,
> >  
> > I am using SUSE Linux 10.1 and i am building for mpc832x.
> >  
> > As I am executing command ./ltib, It gives build faild for the lkc 
> > package.
> >  
> > I have removed whole ltib folder and started again with install and 
> > run command ./ltib
> >  
> > then also it shows build faild. I have attached host_config.log file 
> > with this message.
> >  
> > I can't identify the problem. Help me to solve it.
> >  
> > Regard,
> > dharmesh desai
> >  
> > _______________________________________________
> > Ltib mailing list
> > address@hidden
> > http://lists.nongnu.org/mailman/listinfo/ltib
> 
> 
> 
> _______________________________________________
> Ltib mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/ltib
>