Re: [Ltib] connect to bitshrine.org

[hong zhang]

Kurt,

I tried release 5 and find DirectFB and
DirectFB-examples cause compile error.

Can you verify it?

---henry

--- Kurt Mahan <address@hidden> wrote:

> Henry,
> 
> Release 4 of the MX31 bsp, which is based on
> 2.6.19.2, should have the
> bluez package in it.
> 
> Kurt
> 
> hong zhang wrote:
> > Stuart,
> >
> > Freescale version 2.6.19.2 does not have bluez
> package
> > but 2.6.22 version has bluez utility.
> >
> > I have ported 2.6.19.2 to my custom board that has
> > bluetooth chip. To port 2.6.22 will take a while.
> >
> > How can I port bluez in 2.6.22 to 2.6.19.2 ltib?
> >
> > ---henry
> >
> > --- Stuart Hughes <address@hidden> wrote:
> >
> >   
> >> Hi Henry,
> >>
> >> 1. To check the toolchain version you can either
> do:
> >>
> >> $ ./ltib -m config
> >>
> >> and then look down in the toolchain section to
> see
> >> what you have
> >> selected.
> >>
> >> You can also see more details about the toolchain
> by
> >> looking at
> >> config/platform/<target>/.config
> >>
> >> 2. You get ltib iso images from Freescale's
> website.
> >>
> >> 3. If you're debugging the kernel, then you'll
> need
> >> CodeWarrior/CodeTap
> >> or something similar (hardware debug).  If the
> >> system boots and it's a
> >> user space program you need to debug then you can
> >> use gdb built by ltib.
> >>
> >> Regards, Stuart
> >>
> >> On Thu, 2007-10-18 at 09:52 -0700, hong zhang
> wrote:
> >>     
> >>> Stuart,
> >>>
> >>> I got ltib from freescale imx31ads release and
> >>>       
> >> port it
> >>     
> >>> to a custom board. It is iso version from
> >>>       
> >> freescale.
> >>     
> >>> 1. How do I check toolchain version used in
> ltib?
> >>> 2. where do I get iso version ltib package?
> >>> 3. I am porting package from freescale to custom
> >>>       
> >> board
> >>     
> >>> and have problem for booting, may I use gdb to
> >>>       
> >> debug?
> >>     
> >>> Or I have to bring up board and then use gdb to
> >>>       
> >> debug
> >>     
> >>> non kernel program?
> >>>
> >>> ---henry
> >>>
> >>> --- Stuart Hughes <address@hidden> wrote:
> >>>
> >>>       
> >>>> Hi Henry,
> >>>>
> >>>> It depends where you got your LTIB from (was it
> >>>>         
> >> an
> >>     
> >>>> iso image or from
> >>>> bitshrine.org/savannah?).  If it was an iso
> >>>>         
> >> image
> >>     
> >>>> then those files
> >>>> should have been placed on your local machine
> in
> >>>> /opt/freescale/pkgs/
> >>>> and so there would be no need to go out to the
> >>>> Internet.
> >>>>
> >>>> If you got LTIB from bitshrine/savannah then
> any
> >>>> package that you select
> >>>> who's content is not locally cached in
> >>>> /opt/ltib/pkgs
> >>>> or /opt/freescale/pkgs will need to be fetched
> >>>>         
> >> from
> >>     
> >>>> bitshrine.org over
> >>>> the Internet.
> >>>>
> >>>> Regards, Stuart
> >>>>
> >>>> On Wed, 2007-10-17 at 09:47 -0700, hong zhang
> >>>>         
> >> wrote:
> >>     
> >>>>> List,
> >>>>>
> >>>>> If my host machine does not connect to
> >>>>>           
> >> internet,
> >>     
> >>>> when
> >>>>         
> >>>>> DirectFB, GDB are selected. Build is always
> >>>>>           
> >> failed
> >>     
> >>>> for
> >>>>         
> >>>>> not finding bitshrine.org. Why LTIB does not
> >>>>>           
> >> have
> >>     
> >>>>> source code for them?
> >>>>>
> >>>>> ---henry
> > _______________________________________________
> > LTIB home page: http://bitshrine.org
> >
> > Ltib mailing list
> > address@hidden
> > http://lists.nongnu.org/mailman/listinfo/ltib
> >   
> 
> 


__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around 
http://mail.yahoo.com