Re: [Ltib] Trouble adding new package in LTIB

[James E. Chargin Jr.]

Luis,

That did the trick, thanks.

I'll attempt to solve my next problems (compiler errors) without asking 
for help for a while, to avoid asking another question with an obvious 
answer.

Thanks again,
Jim



Luis Felipe Strano Moraes wrote:
> 2008/8/15 James E. Chargin Jr. <address@hidden>:
> > Thanks for the detailed explanation.
> >
> > I have added the md5 as Peter suggested.
> > I have also "activated" the package via LTIB. On exit from LTIB, I get
> > output from rpmbuild. During this, I get the message (which I mentioned
> > previously):
> >
> > 8--
> > configure: error: termcap could not be found which is required for the
> > --with-readline option (which is enabled by default).  Either disable
> > readline support with --without-readline or download and install termcap
> > from:
> >        ftp.gnu.org/gnu/termcap
> > Note: if you are using precompiled packages you will also need the
> > development package as well (which may be called termcap-devel or something
> > similar).
> > Note: (n)curses also seems to work as a substitute for termcap.  This was
> > not found either - but you could try installing that as well.
> > --8
> >
> > As I indicated, I need help with this. I would prefer (I think) to build
> > without termcap, rather than include it on my embedded system, but I don't
> > know where I would specify --without-readline.  I know this would be a
> > command line parameter for configure, but I don't know where that command
> > line is generated.
> Inside the .spec file, on the %Build stage.
>
> --lf
>
> > Could someone provide guidance?
> >
> > Thank you very much,
> > Jim
> >
> >
> > Stuart Hughes wrote:
> > > On Thu, 2008-08-14 at 15:02 -0400, Peter Barada wrote:
> > > > On Thu, 2008-08-14 at 09:07 -0700, James E. Chargin Jr. wrote:
> > > > > Processing: parted
> > > > > ====================
> > > > > Testing network connectivity
> > > > > Testing proxy connection for GPP : FAIL
> > > > > response was: 500 Can't connect to wwwgate0.freescale.net:1080 (Bad
> > > > > hostname 'wwwgate0.freescale.net')
> > > > > Can't get gpp index, proxy forced off
> > > > > FAILED PPP: : 500 Can't connect to auslxsc01.mtwk.freescale.net:80 (Bad
> > > > > hostname 'auslxsc01.mtwk.freescale.net')
> > > > > OK GPP:
> > > > >
> > > > > FAILED GPP: parted-1.8.8.tar.bz2.md5: 404 Not Found
> > > > > WARN: skipping md5sum check for
> > > > > /opt/freescale/pkgs/parted-1.8.8.tar.bz2, md5 file was not found
> > > > When you add a new package to the system, add a md5sum file to
> > > > /opt/freescale/pkgs:
> > > >
> > > > $ pushd /opt/freescale/pkgs
> > > > $ md5sum parted-1.8.8.tar.bz2 > parted-1.8.8.tar.bz2.md5
> > > The .md5sum file will be created if/when you eventually upload the content
> > > to the GPP.  However until then this a good thing to do aswell.
> > >
> > > > LTIB looks for the .md5 to be sure that what you have is not corrupt, and
> > > > if it doesn't find the .md5 in /opt/freescale/pkgs/ it looks int the Global
> > > > Package Pool and Private Package Pool.  The global pool is in
> > > > www.bitshrine.org/gpp, <http://www.bitshrine.org/gpp,> but hte provate pool
> > > > is in Freescale (your BSP came from them), which can't be seen by your
> > > > machine since you're outside Freescale's network.  It would be nice if
> > > > Freescale would disable the Provate Package Pool on .iso BSPs they release
> > > > to remove this problem.
> > > On later BSPs the PPP references are scrubbed.  These messages can be
> > > ignored, but if they're nuisance, edit .ltibrc and delete the entry for the
> > > ppp.
> > >
> > > Regards, Stuart
> >
> > _______________________________________________
> > LTIB home page: http://bitshrine.org
> >
> > Ltib mailing list
> > address@hidden
> > http://lists.nongnu.org/mailman/listinfo/ltib