Linux version 2.6.34 (address@hidden) (gcc version 4.1.2) #6 PREEMPT Wed Jun 30 18:37:42 CST 2010 CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: Phytec 3250 board with the LPC3250 Microcontroller Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,115200n81 root=/dev/mtdblock3 rw rootfstype=jffs2 ip=dhcp init=/sbin/init PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 61252k/61252k available, 4284k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xc4800000 - 0xf0000000 ( 696 MB) lowmem : 0xc0000000 - 0xc4000000 ( 64 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc0025000 ( 116 kB) .text : 0xc0025000 - 0xc0342000 (3188 kB) .data : 0xc0342000 - 0xc0365d80 ( 144 kB) Hierarchical RCU implementation. NR_IRQS:96 Console: colour dummy device 80x30 Calibrating delay loop... 103.83 BogoMIPS (lpj=519168) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 LPC32XX DMA driver LPC32XX unique ID: 0006291c75701b6e58dc8cb710a97400 bio: create slab at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb Switching to clocksource lpc32xx_clksrc NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) ? 2001-2006 Red Hat, Inc. msgmni has been set to 119 alg: No test for stdrng (krng) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x40090000 (irq = 9) is a 16550A console [ttyS0] enabled serial8250.0: ttyS1 at MMIO 0x40080000 (irq = 7) is a 16550A serial8250.0: ttyS2 at MMIO 0x40088000 (irq = 8) is a 16550A serial8250.0: ttyS3 at MMIO 0x40098000 (irq = 10) is a 16550A lpc32xx_hsuart.0: ttyTX0 at MMIO 0x40014000 (irq = 26) is a lpc32xx_hsuart lpc32xx_hsuart.0: ttyTX1 at MMIO 0x40018000 (irq = 25) is a lpc32xx_hsuart lpc32xx_hsuart.0: ttyTX2 at MMIO 0x4001c000 (irq = 24) is a lpc32xx_hsuart brd: module loaded loop: module loaded NAND device: Manufacturer ID: 0xad, Chip ID: 0x76 (Hynix NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 4 MTD partitions on "lpc32xx_nand": 0x000000000000-0x000000168000 : "phy3250-boot" 0x000000168000-0x000000190000 : "phy3250-ubt-prms" 0x000000190000-0x000000590000 : "phy3250-kernel" 0x000000590000-0x000004000000 : "phy3250-rootfs" ssp-pl022 dev:ssp0: ARM PL022 driver, device ID: 0x00041022 pl022: mapped registers from 0x20084000 to c4882000 at25 spi0.0: 32 KByte at25256a eeprom, pagesize 64 eth%d: Invalid ethernet MAC address. Please set using ifconfig lpc_mii_bus: probed eth0: using RMII interface eth0: LPC mac at 0x31060000 irq 29 eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=0:00, irq=-1) usbmon: debugfs is not available ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver ISP1301 Vendor ID : 0x04cc ISP1301 Product ID : 0x1301 ISP1301 Version ID : 0x0210 usb-ohci usb-ohci: at 0xf3120000, irq 0 usb-ohci usb-ohci: pnx4008 OHCI usb-ohci usb-ohci: new USB bus registered, assigned bus number 1 usb-ohci usb-ohci: irq 59, io mem 0xf3120000 usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: pnx4008 OHCI usb usb1: Manufacturer: Linux 2.6.34 ohci_hcd usb usb1: SerialNumber: usb-ohci hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual rtc-lpc32xx rtc-lpc32xx: rtc core: registered rtc-lpc32xx as rtc0 i2c /dev entries driver PNX4008-WDT: PNX4008 Watchdog Timer: heartbeat 19 sec cpuidle: using governor ladder cpuidle: using governor menu mmci-pl18x: DMA buffer(10000 bytes), P:0x83d60000, V:0xffc01000 mmci-pl18x dev:mmc0: mmc0: MMCI rev 0 cfg 00 at 0x0000000020098000 irq 15,13 TCP cubic registered NET: Registered protocol family 17 VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 1 rtc-lpc32xx rtc-lpc32xx: setting system clock to 1970-01-01 01:31:21 UTC (5481) IP-Config: Failed to open eth0 IP-Config: No network devices available. Empty flash at 0x00ac08f0 ends at 0x00ac0a00 JFFS2 error: (1) jffs2_build_inode_pass1: child dir "lib" (ino #3897) of dir ino #3886 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "pub" (ino #3898) of dir ino #3886 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "bin" (ino #3900) of dir ino #3891 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "lpd" (ino #3902) of dir ino #3892 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "mail" (ino #3903) of dir ino #3892 appears to be a hard link JFFS2 error: (1) jffs2_build_inode_pass1: child dir "cgi-bin" (ino #3904) of dir ino #3894 appears to be a hard link VFS: Mounted root (jffs2 filesystem) on device 31:3. Freeing init memory: 116K init started: BusyBox v1.11.2 () starting pid 333, tty '': '/etc/rc.d/rcS' Mounting /proc and /sys Setting the hostname to Climax-Net3 Mounting filesystems JFFS2 warning: (355) jffs2_get_inode_nodes: Eep. No valid nodes for ino #3906. JFFS2 warning: (355) jffs2_do_read_inode_internal: no data nodes found for ino #3906 iget() failed for ino #3906 cp: cannot stat '/var/ftp/etc/utmp': Input/output error JFFS2 warning: (355) jffs2_get_inode_nodes: Eep. No valid nodes for ino #3902. JFFS2 warning: (355) jffs2_do_read_inode_internal: no data nodes found for ino #3902 iget() failed for ino #3902 cp: cannot stat '/var/run/lib': JFFS2 warning: (355) jffs2_get_inode_nodes: Eep. No valid nodes for ino #3903. Input/output error JFFS2 warning: (355) jffs2_do_read_inode_internal: no data nodes found for ino #3903 iget() failed for ino #3903 cp: cannot stat '/var/run/pub': Input/output error mount: mounting usbfs on /proc/bus/usb failed: No such file or directory Starting syslogd and klogd Running sysctl Setting up networking on loopback device: Setting up networking on eth0: /etc/rc.d/init.d/network: line 162: udhcpc: not found Starting inetd: Starting the dropbear ssh server: starting pid 393, tty '': '-/bin/sh'