Here is the verbose output. Looks like verbose output begins and
ends at
process start up (host/domain names changed):
Starting Process Monitor (monit): monit: Debug: Adding host allow
'localhost'
monit: Debug: Skipping redundant host 'localhost'
monit: Debug: Skipping redundant host 'localhost'
monit: Debug: Adding credentials for user 'admin'.
Runtime constants:
Control file = /etc/monit.conf
Log file = syslog
Pid file = /var/run/monit.pid
Debug = True
Log = True
Use syslog = True
Is Daemon = True
Use process engine = True
Poll time = 60 seconds
Mail server(s) = prodsmtp.mydomain.net
Mail from = address@hidden
Mail subject = monit alert -- $EVENT $SERVICE
Mail message = $EVENT Service $SERV..(truncated)
Start monit httpd = True
httpd bind address = localhost
httpd portnumber = 2812
httpd signature = True
Use ssl encryption = False
httpd auth. style = Basic Authentication and Host/Net allow list
Alert mail to = address@hidden
Alert on = All events
The service list contains the following entries:
Process Name = ntpd
Pid file = /var/run/ntpd.pid
Monitoring mode = active
Start program = '/etc/init.d/ntpd start' timeout 1 cycle(s)
Stop program = '/etc/init.d/ntpd stop' timeout 1 cycle(s)
Pid = if changed 1 times within 1 cycle(s) then alert
Ppid = if changed 1 times within 1 cycle(s) then alert
Timeout = If 3 restart within 3 cycles then unmonitor
else if
passed then alert
System Name = test-prod.mydomain.net
Monitoring mode = active
----------------------------------------------------------------------------
---
monit: pidfile '/var/run/monit.pid' does not exist
Starting monit daemon with http interface at [localhost:2812]
Then when ntp is killed I see the following in /var/log/messages:
Jan 16 19:10:50 test-prod ntpd[13505]: ntpd exiting on signal 15
Jan 16 19:11:32 test-prod monit[2398]: 'ntpd' process is not running
Jan 16 19:11:32 test-prod monit[2398]: 'ntpd' trying to restart
Jan 16 19:11:32 test-prod monit[2398]: 'ntpd' start: /etc/init.d/ntpd
Jan 16 19:11:32 test-prod ntpd[2541]: ntpd address@hidden Tue Jun 10
00:07:18 UTC 2008 (1)
Jan 16 19:11:32 test-prod ntpd[2542]: precision = 2.000 usec
.
.
There is no additional output from monit and no attempt to send mail
according to maillog.
On 1/16/09 3:52 AM, "Jan-Henrik Haukeland" <address@hidden>
wrote:
Have you tried to specify which mail server Monit should use for
alerts?
See
http://mmonit.com/monit/documentation/monit.html#setting_a_mail_server_for_ale
rt_messages
On 16. jan.. 2009, at 08.00, Bruce Reed wrote:
I’ve just begun using monit and I am having difficulties getting
monit to send mail. I’m testing using ntpd and it is restarting the
process, but not sending mail on service restart events or timeout.
In monit.conf I have:
set alert address@hidden
I then had a check statement like this:
check process ntpd with pidfile /var/run/ntpd.pid
start program = "/etc/init.d/ntpd start"
stop program = "/etc/init.d/ntpd stop"
if 3 restarts within 3 cycles then timeout
alert address@hidden only on { timeout }
After 3 successive kills of ntpd and restarts by monit, a timeout
message was logged, but no mail was sent. I tried removing the alert
statement to see if mail would be sent on any event, but I only see
information iogged and no mail is sent. Nothing in /var/log/maillog
either.
Funny thing is, when I first set this up monit attempted to send
mail, but an ACL on my postifx server prevented it from getting
through. I fixed that and retried my test, but from that point on no
mail was sent. Thought perhaps this was a state caching issue, but
no change across monit restart and I installed monit on another
server using the same conf files and I get the same results there.
Thanks,
Bruce
--
To unsubscribe:
http://lists.nongnu.org/mailman/listinfo/monit-general
--
To unsubscribe:
http://lists.nongnu.org/mailman/listinfo/monit-general