☺ Buildbot (GNU Toolchain): gnupoke - build successful (master)

[builder]

A restored build has been detected on builder gnupoke-debian-testing-x86_64 
while building gnupoke.

Full details are available at:
    https://builder.sourceware.org/buildbot/#builders/218/builds/2

Build state: build successful
Revision: 52fd6468b803c8561762172d961c92c0b298d728
Worker: bb2-1
Build Reason: (unknown)
Blamelist: Arsen Arsenović <arsen@aarsen.me>, Jose E. Marchesi 
<jose.marchesi@oracle.com>

Steps:

- 0: worker_preparation ( success )

- 1: git checkout ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/1/logs/stdio

- 2: bootstrap ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/2/logs/stdio

- 3: configure ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/3/logs/stdio

- 4: make ( warnings )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/4/logs/stdio
        - warnings (6): 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/4/logs/warnings__6_

- 5: make check ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/5/logs/stdio

- 6: prep ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/6/logs/stdio

- 7: fetch ['./testsuite/poke.log'] ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/7/logs/stdio

- 8: fetch ['config.log'] ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/8/logs/stdio

- 9: fetch ['./jitter/config.log'] ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/9/logs/stdio

- 10: pass .bunsen.source.gitname ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/10/logs/stdio

- 11: pass .bunsen.source.gitdescribe ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/11/logs/stdio

- 12: pass .bunsen.source.gitbranch ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/12/logs/stdio

- 13: pass .bunsen.source.gitrepo ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/13/logs/stdio

- 14: upload to bunsen ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/14/logs/stdio

- 15: clean up ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/2/steps/15/logs/stdio