☠ Buildbot (GNU Toolchain): gnupoke - failed test (failure) (master)

[builder]

A new failure has been detected on builder gnupoke-debian-testing-x86_64 while 
building gnupoke.

Full details are available at:
    https://builder.sourceware.org/buildbot/#builders/218/builds/20

Build state: failed test (failure)
Revision: 6c0a476085476418a5708cb61e9165657d38803a
Worker: bb2-2
Build Reason: (unknown)
Blamelist: Jose E. Marchesi <jose.marchesi@oracle.com>

Steps:

- 0: worker_preparation ( success )

- 1: git checkout ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/1/logs/stdio

- 2: bootstrap ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/2/logs/stdio

- 3: configure ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/3/logs/stdio

- 4: make ( warnings )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/4/logs/stdio
        - warnings (3): 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/4/logs/warnings__3_

- 5: make check ( failure )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/5/logs/stdio

- 6: prep ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/6/logs/stdio

- 7: build bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/7/logs/stdio

- 8: fetch bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/8/logs/stdio

- 9: unpack bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/9/logs/stdio

- 10: pass .bunsen.source.gitname ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/10/logs/stdio

- 11: pass .bunsen.source.gitdescribe ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/11/logs/stdio

- 12: pass .bunsen.source.gitbranch ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/12/logs/stdio

- 13: pass .bunsen.source.gitrepo ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/13/logs/stdio

- 14: upload to bunsen ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/14/logs/stdio

- 15: clean up ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/218/builds/20/steps/15/logs/stdio

A new failure has been detected on builder gnupoke-debian-i386 while building 
gnupoke.

Full details are available at:
    https://builder.sourceware.org/buildbot/#builders/219/builds/17

Build state: failed test (failure)
Revision: 6c0a476085476418a5708cb61e9165657d38803a
Worker: debian-i386-2
Build Reason: (unknown)
Blamelist: Jose E. Marchesi <jose.marchesi@oracle.com>

Steps:

- 0: worker_preparation ( success )

- 1: git checkout ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/1/logs/stdio

- 2: bootstrap ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/2/logs/stdio

- 3: configure ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/3/logs/stdio

- 4: make ( warnings )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/4/logs/stdio
        - warnings (4): 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/4/logs/warnings__4_

- 5: make check ( failure )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/5/logs/stdio

- 6: prep ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/6/logs/stdio

- 7: build bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/7/logs/stdio

- 8: fetch bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/8/logs/stdio

- 9: unpack bunsen.cpio.gz ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/9/logs/stdio

- 10: pass .bunsen.source.gitname ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/10/logs/stdio

- 11: pass .bunsen.source.gitdescribe ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/11/logs/stdio

- 12: pass .bunsen.source.gitbranch ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/12/logs/stdio

- 13: pass .bunsen.source.gitrepo ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/13/logs/stdio

- 14: upload to bunsen ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/14/logs/stdio

- 15: clean up ( success )
    Logs:
        - stdio: 
https://builder.sourceware.org/buildbot/#builders/219/builds/17/steps/15/logs/stdio