Re: [PATCH qemu] x86: don't let decompressed kernel image clobber setup_data

[Philippe Mathieu-Daudé]

Hi Jason,

On 28/12/22 15:38, Jason A. Donenfeld wrote:
> The setup_data links are appended to the compressed kernel image. Since
> the kernel image is typically loaded at 0x100000, setup_data lives at
> `0x100000 + compressed_size`, which does not get relocated during the
> kernel's boot process.
>
> The kernel typically decompresses the image starting at address
> 0x1000000 (note: there's one more zero there than the decompressed image
> above). This usually is fine for most kernels.
>
> However, if the compressed image is actually quite large, then
> setup_data will live at a `0x100000 + compressed_size` that extends into
> the decompressed zone at 0x1000000. In other words, if compressed_size
> is larger than `0x1000000 - 0x100000`, then the decompression step will
> clobber setup_data, resulting in crashes.
>
> Fix this by detecting that possibility, and if it occurs, put setup_data
> *after* the end of the decompressed kernel, so that it doesn't get
> clobbered.
>
> One caveat is that this only works for images less than around 64
> megabytes, so just bail out in that case. This is unfortunate, but I
> don't currently have a way of fixing it.
>
> Cc: x86@kernel.org
> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
> ---
>   hw/i386/x86.c | 30 ++++++++++++++++++++++++++++++
>   1 file changed, 30 insertions(+)
>
> diff --git a/hw/i386/x86.c b/hw/i386/x86.c
> index 78cc131926..628fd2b2e9 100644
> --- a/hw/i386/x86.c
> +++ b/hw/i386/x86.c
> @@ -1077,6 +1077,36 @@ void x86_load_linux(X86MachineState *x86ms,
>       }
>       fclose(f);
>   
> +    /* If a setup_data is going to be used, make sure that the bootloader won't
> +     * decompress into it and clobber those bytes. */
> +    if (dtb_filename || !legacy_no_rng_seed) {
> +        uint32_t payload_offset = ldl_p(setup + 0x248);
> +        uint32_t payload_length = ldl_p(setup + 0x24c);
> +        uint32_t target_address = ldl_p(setup + 0x258);

Nitpicking, can the Linux kernel add these magic values in
arch/x86/include/uapi/asm/bootparam.h? Or can we use
offsetof(setup_header) to get them?

> +        uint32_t decompressed_length = ldl_p(kernel + payload_offset + 
> payload_length - 4);
> +
> +        uint32_t estimated_setup_data_length = 4096 * 16;
> +        uint32_t start_setup_data = prot_addr + kernel_size;
> +        uint32_t end_setup_data = start_setup_data + 
> estimated_setup_data_length;
> +        uint32_t start_target = target_address;
> +        uint32_t end_target = target_address + decompressed_length;

Maybe we can simply use 'unsigned' type.

> +        if ((start_setup_data >= start_target && start_setup_data < 
> end_target) ||
> +            (end_setup_data >= start_target && end_setup_data < end_target)) {
> +            uint32_t padded_size = target_address + decompressed_length - 
> prot_addr;
> +
> +            /* The early stage can't address past around 64 MB from the 
> original
> +             * mapping, so just give up in that case. */
> +            if (padded_size < 62 * 1024 * 1024)

You mention 64 but check for 62, is that expected? You can use the MiB
definitions to ease code review: 64 * MiB.

> +                kernel_size = padded_size;
> +            else {
> +                fprintf(stderr, "qemu: Kernel image too large to hold 
> setup_data\n");
> +                dtb_filename = NULL;
> +                legacy_no_rng_seed = true;
> +            }
> +        }
> +    }
Fix looks good, glad you figured out the problem.

Regards,

Phil.