[Stable-8.2.1 50/54] hw/scsi/esp-pci: synchronise setting of DMA_STAT_DONE with ESP completion interrupt

[Michael Tokarev]

From: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>

The setting of DMA_STAT_DONE at the end of a DMA transfer can be configured to
generate an interrupt, however the Linux driver manually checks for 
DMA_STAT_DONE
being set and if it is, considers that a DMA transfer has completed.

If DMA_STAT_DONE is set but the ESP device isn't indicating an interrupt then
the Linux driver considers this to be a spurious interrupt. However this can
occur in QEMU as there is a delay between the end of DMA transfer where
DMA_STAT_DONE is set, and the ESP device raising its completion interrupt.

This appears to be an incorrect assumption in the Linux driver as the ESP and
PCI DMA interrupt sources are separate (and may not be raised exactly
together), however we can work around this by synchronising the setting of
DMA_STAT_DONE at the end of a DMA transfer with the ESP completion interrupt.

In conjunction with the previous commit Linux is now able to correctly boot
from an am53c974 PCI SCSI device on the hppa C3700 machine without emitting
"iget: checksum invalid" and "Spurious irq, sreg=10" errors.

Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
(cherry picked from commit 1e8e6644e063b20ad391140fae13d00ad7750b33)
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>

diff --git a/hw/scsi/esp-pci.c b/hw/scsi/esp-pci.c
index d29c8c25bd..b1bd43b7db 100644
--- a/hw/scsi/esp-pci.c
+++ b/hw/scsi/esp-pci.c
@@ -93,6 +93,18 @@ static void esp_irq_handler(void *opaque, int irq_num, int 
level)
 
     if (level) {
         pci->dma_regs[DMA_STAT] |= DMA_STAT_SCSIINT;
+
+        /*
+         * If raising the ESP IRQ to indicate end of DMA transfer, set
+         * DMA_STAT_DONE at the same time. In theory this should be done in
+         * esp_pci_dma_memory_rw(), however there is a delay between setting
+         * DMA_STAT_DONE and the ESP IRQ arriving which is visible to the
+         * guest that can cause confusion e.g. Linux
+         */
+        if ((pci->dma_regs[DMA_CMD] & DMA_CMD_MASK) == 0x3 &&
+            pci->dma_regs[DMA_WBC] == 0) {
+                pci->dma_regs[DMA_STAT] |= DMA_STAT_DONE;
+        }
     } else {
         pci->dma_regs[DMA_STAT] &= ~DMA_STAT_SCSIINT;
     }
@@ -306,9 +318,6 @@ static void esp_pci_dma_memory_rw(PCIESPState *pci, uint8_t 
*buf, int len,
     /* update status registers */
     pci->dma_regs[DMA_WBC] -= len;
     pci->dma_regs[DMA_WAC] += len;
-    if (pci->dma_regs[DMA_WBC] == 0) {
-        pci->dma_regs[DMA_STAT] |= DMA_STAT_DONE;
-    }
 }
 
 static void esp_pci_dma_memory_read(void *opaque, uint8_t *buf, int len)
@@ -363,24 +372,13 @@ static const VMStateDescription vmstate_esp_pci_scsi = {
     }
 };
 
-static void esp_pci_command_complete(SCSIRequest *req, size_t resid)
-{
-    ESPState *s = req->hba_private;
-    PCIESPState *pci = container_of(s, PCIESPState, esp);
-
-    esp_command_complete(req, resid);
-    pci->dma_regs[DMA_WBC] = 0;
-    pci->dma_regs[DMA_STAT] |= DMA_STAT_DONE;
-    esp_pci_update_irq(pci);
-}
-
 static const struct SCSIBusInfo esp_pci_scsi_info = {
     .tcq = false,
     .max_target = ESP_MAX_DEVS,
     .max_lun = 7,
 
     .transfer_data = esp_transfer_data,
-    .complete = esp_pci_command_complete,
+    .complete = esp_command_complete,
     .cancel = esp_request_cancelled,
 };
 
-- 
2.39.2