RE: [avr-gcc-list] debugger info

[franz r]

Hi,

I found it on 
http://www.pvv.ntnu.no/~torhr/avrmon-stk200/

Regards,
Franz Reich

>>>>>>>>>>>>>>>>>> Ursprüngliche Nachricht <<<<<<<<<<<<<<<<<<

Am 26.11.2001, 23:05:57, schrieb "Ross Wakelin" <address@hidden> zum 
Thema RE: [avr-gcc-list] debugger info:


> no, but I would like to know about it...

> ----------
> Ross Wakelin - Independent Information Technology Consultant
> Tel: +64 (0)3 3433186  Fax: +64 (0)3 3433196
> Cell: +64 (0)21 334380

> -----Original Message-----
> From: address@hidden
> [mailto:address@hidden On Behalf Of Robert Rozman
> Sent: Tuesday, 27 November 2001 09:59
> To: address@hidden
> Subject: Re: [avr-gcc-list] debugger info


> Hello,

> nobody mentioned low cost in circuit debugging via stk 200 dongle in
> -Linux with help of avrmon. Anyone using that ?

> Regards,

> Robert Rozman
> address@hidden
> ----- Original Message -----
> From: "Scott Finneran" <address@hidden>
> To: <address@hidden>
> Cc: <address@hidden>
> Sent: 26. november 2001 2:54
> Subject: Re: [avr-gcc-list] debugger info


> > Ross,
> >
> > There is a link on the website to the Atmel site. It is their product.

> > I believe that it retails for around US$250 (quite reasonable for a
> > JTAG box in my limited experience).
> >
> > A review of it should be on avrfreaks (http://www.avrfreaks.net).
> > note: This review deals deals with the Atmel JTAG ICE being used with
> > AVR
> Studio.
> >
> > Cheers,
> >
> > scott Finneran
> >
> > Ross Wakelin wrote:
> >
> > > Ooookay, so where do I get one of these JTAG thingies,
> > > and how much does it cost......
> > >
> > > Thanks
> > >
> > > ----------
> > > Ross Wakelin - Independent Information Technology Consultant
> > > Tel: +64 (0)3 3433186  Fax: +64 (0)3 3433196
> > > Cell: +64 (0)21 334380
> > >
> > > -----Original Message-----
> > > From: Scott Finneran [mailto:address@hidden
> > > Sent: Monday, 26 November 2001 11:41
> > > To: address@hidden
> > > Cc: address@hidden
> > > Subject: Re: [avr-gcc-list] debugger info
> > >
> > >
> > > Hello Ross,
> > >
> > > Check out AVaRICE(http://avarice.sourceforge.net). It is free(GPL)
> > > and allows you to interface the Atmel AVR JTAG ICE with gdb.
> > >
> > > Regards,
> > >
> > > Scott Finneran
> > >
> > > Ross Wakelin wrote:
> > >
> > >
> > >>Hi,
> > >>
> > >>I'm just starting with the Atmel line of chips, and
> > >>have an ABC maxi as my test bed.  I am using the latest
> > >>GCC tool chain downloaded from AVR freaks.
> > >>
> > >>How are you supposed to do debugging, especially
> > >>in circuit debugging, in this sort of environment?
> > >>
> > >>Thanks
> > >>
> >
> >
> >
> > _______________________________________________
> > avr-gcc-list mailing list
> > address@hidden
> > http://avr.jpk.co.nz/mailman/listinfo/avr-gcc-list


> _______________________________________________
> avr-gcc-list mailing list
> address@hidden
> http://avr.jpk.co.nz/mailman/listinfo/avr-gcc-list




> _______________________________________________
> avr-gcc-list mailing list
> address@hidden
> http://avr.jpk.co.nz/mailman/listinfo/avr-gcc-list