Re: [Ltib] Compile Qt5 under LTIB?

[Stuart Hughes]

Hi Peter,

I don't know if it helps, but getting Qt3/4 to build under LTIB was a
horrible, so by way of encouragement just keep chipping away.

Regards, Stuart

On 27/09/13 19:41, Peter Barada wrote:
> Anyone have luck building Qt5 under LTIB?  I've been trying and am not
> having success.
> 
> Using the release
> http://download.qt-project.org/official_releases/qt/5.1/5.1.1/single/qt-everywhere-opensource-src-5.1.1.tar.gz
> 
> 
> I tried to target a beagleboard (as a step to getting it to run on my
> OMAP dm37x board) using the following %Build stanza in a new
> qtopia-5.1.1.spec file:
> 
> %Build
> 
> export PATH="/usr/bin/:$PATH"
> 
> export AR=''
> export CC=''
> export CXX=''
> export LD=''
> 
> export QMAKESPEC=""
> export PKG_CONFIG="pkg-config --define-variable=prefix=$TOP/rootfs/usr/ " 
> export PKG_CONFIG_PATH=$TOP/rootfs/usr/lib/pkgconfig 
> export PKG_CONFIG_SYSROOT=$TOP/rootfs/
> 
> ./configure -opensource -confirm-license -device linux-beagleboard-g++
> -device-option CROSS_COMPILE=$TOOLCHAIN_PATH/bin/arm-none-linux-gnueabi-
> -no-eglfs -no-kms -no-icu -no-xcb -no-c++11
> 
> make -j1
> 
> I modified the source via the attached patch (to fix
> https://bugreports.qt-project.org/browse/QTBUG-33300), and now it fails
> with:
> 
> Project ERROR: Unknown module(s) in QT: quick
> make[3]: *** [sub-declarative-radio-make_first] Error 3
> make[3]: Leaving directory
> `/home/peter/work/logic/eps_svn/software/products/linux/LTIB/trunk/ltib-3.0-qt5/rpm/BUILD/qt-everywhere-opensource-src-5.1.1/qtmultimedia/examples/multimedia'
> make[2]: *** [sub-multimedia-make_first] Error 2
> make[2]: Leaving directory
> `/home/peter/work/logic/eps_svn/software/products/linux/LTIB/trunk/ltib-3.0-qt5/rpm/BUILD/qt-everywhere-opensource-src-5.1.1/qtmultimedia/examples'
> make[1]: *** [sub-examples-make_first] Error 2
> make[1]: Leaving directory
> `/home/peter/work/logic/eps_svn/software/products/linux/LTIB/trunk/ltib-3.0-qt5/rpm/BUILD/qt-everywhere-opensource-src-5.1.1/qtmultimedia'
> make: *** [module-qtmultimedia-make_first] Error 2
> error: Bad exit status from
> /home/peter/work/logic/eps_svn/software/products/linux/LTIB/trunk/ltib-3.0-qt5/tmp/rpm-tmp.17783
> (%build)
> 
> I can't build with the "quick" module since I don't have OpenGL in my
> world (wonder why Qt5 didn't figure this out from the "-no-opengl"
> confugure option) but trying to add "-skip quick" causes Qt5 configure
> to fail with "no such module qtquick".
> 
> Any help on getting Qt5 to build under LTIB is appreciated.  Thanks in
> advance!
> 
> 
> 
> _______________________________________________
> LTIB home page: http://ltib.org
> 
> Ltib mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/ltib
>