and my PC (not the host, or guest) is seen on br0. My PC should be seen on eth0 I think and only the virtual machine should be see from the br0. Hope somebody could tell me what is going on here.
보낸 사람 : "김찬" <address@hidden>
보낸 날짜 : 2014-09-18 22:09:00 ( +09:00 )
받는 사람 : address@hidden <address@hidden>
참조 :
제목 : RE: need help in setting up tap networking for using qemu virtual machine
Forgot to mention that while qemu is running with RTEMS telnetd.exe, (with ETH0IP set to 48)
from the host I get ping response from 47 and 48. But I cannot ping to google.com.
and when I type in the password at telnet, I can get in to both.
(but couple of times got 'connection close by foreign host.' I remember)
Thanks a lot.
Chan Kim
보낸 사람 : "김찬"
보낸 날짜 : 2014-09-18 22:00:32 ( +09:00 )
받는 사람 : address@hidden
참조 :
제목 : need help in setting up tap networking for using qemu virtual machine
Hello, everyone!
It's good to have some people to ask this.. I really need a help from you and this should be a basic question.
I'm trying to run a virtual machine (using qemu-system-sparc, I added lan9220 emulation model inside) on my CentOS 6.4 machine.
I've read [url]http://www.linuxquestions.org/questions/linux-virtualization-and-cloud-90/centos-6-and-kvm-how-to-setup-bridged-networking-in-kvm-in-a-class-b-environment-4175433990/[/url] but my case seems different and I am not sure if this previous post is
correct or not.
My host ip is 129.254.132.47. and I want my virtual machine to be 129.254.132.48. (it's class B network)
I have /etc/qemu-ifup like this
--------------------- start -------------------------
#!/bin/sh
#
# script to bring up the tun device in QEMU in bridged mode
# first parameter is name of tap device (e.g. tap0)
#
# some constants specific to the local host - change to suit your host
#
# guest 132.48 host 132.47 bridge 132.64
set -x
ETH0IP=129.254.132.47
GATEWAY=129.254.132.1
BROADCAST=129.254.255.255
#
# First take eth0 down, then bring it up with IP address 0.0.0.0
#
/sbin/ifdown eth0
/sbin/ifconfig eth0 0.0.0.0 promisc up
#
# Bring up the tap device (name specified as first argument, by QEMU)
#
/usr/sbin/openvpn --mktun --dev $1 --user `id -un`
/sbin/ifconfig $1 0.0.0.0 promisc up
#
# create the bridge between eth0 and the tap device
#
/usr/sbin/brctl addbr br0
/usr/sbin/brctl addif br0 eth0
/usr/sbin/brctl addif br0 $1
#
# only a single bridge so loops are not possible, turn off spanning tree protocol
#
/usr/sbin/brctl stp br0 off
#
# Bring up the bridge with ETH0IP and add the default route
#
/sbin/ifconfig br0 $ETH0IP netmask 255.255.0.0 broadcast $BROADCAST
/sbin/route add default gw $GATEWAY
#
# stop firewall - comment this out if you don't use Firestarter
#
#/sbin/service firestarter stop
--------------------- end -------------------------
and /etc/qemu-ifdown as
------------------- start --------------------------
#!/bin/sh
#
# Script to bring down and delete bridge br0 when QEMU exits
#
# Bring down eth0 and br0
#
set -x
/sbin/ifdown eth0
/sbin/ifdown br0
/sbin/ifconfig br0 down
#
# Delete the bridge
#
/usr/sbin/brctl delbr br0
#
# bring up eth0 in "normal" mode
#
/sbin/ifconfig eth0 -promisc
/sbin/ifup eth0
#
# delete the tap device
#
/usr/sbin/openvpn --rmtun --dev $1
#
# start firewall again
#
#/sbin/service firestarter start
-------------------- end --------------------------
and I start my virtual machine with this command :
qemu-system-sparc -M ALDEBARAN -serial stdio -kernel telnetd/o-optimize/telnetd.exe -net nic -net tap,ifname=tap0
(this makes /etc/qemu-ifup tap0 and /etc/qemu-ifdown tap0 run before and after qemu run.)
When I run above command, I can see the virtual machine's code is running. (it's RTEMS network-demo program. telnetd.exe)
From outside the host, I can ping to host and the guest. So I thought everything is fine But I then I found something is wrong..
When I telnet to 129.254.132.47, it is centOS as expected.
But when I telnet to 129.254.132.48, it takes unusually long (like 10 seonds?) then I see the loging prompt coming from CentOS.(the host)
I can log into it, and it's my host machine.
(By the way, both telnetting looked hampered by something, like interfering one another by wrong setting..)
I can run the same telnetd program using actual board the qemu emulator is emulating, and I can telnet to the board (and of course it's RTEMS). Only, when using actual board, I use physical network cable between my host and the board. (host 10.10.10.1 and the
board 10.10.10.11)
I tried setting ETH0IP to 129.254.132.47 in qemu-ifup script but it didn't work.
Please anyone tell me what the problem is..
Kind regards,
Chan Kim