bug#33082: guix pull resulted in an error: compute-guix-derivation

[Joshua Branson]

Joshua Branson <address@hidden> writes:

> Well,  I thought I'd try to enable substitutes...
>
> address@hidden guix]# pwd
> /var/guix/profiles/per-user/root/guix-profile/share/guix
>
> guix archive --authorize berlin.guixsd.org.pub 
>
> This commands has been hanging (doing nothing, as far I can tell) for 5+ 
> minutes.  That sounds non-normal.

Ahh I forgot the "<".

 guix archive --authorize < berlin.guixsd.org.pub 


So now I am definitely using substitutes.  I only have a few minutes
before I need to go to work, so I don't think "guix pull" will have
enough time to finish.  I'll have to try again tomorrow.



>
> On Fri, Oct 19, 2018, at 2:11 AM, Ludovic Courtès wrote:
>> Hello,
>> 
>> Gábor Boskovits <address@hidden> skribis:
>> 
>> > Joshua Branson <address@hidden> ezt írta (időpont: 2018. okt.
>> > 18., Cs, 16:51):
>> 
>> [...]
>> 
>> >> Total duration: 8 min 47 sec
>> >> Tests result: FAILURE
>> >> make: *** [Makefile:869: test] Error 2
>> >>
>> >> Test suite failed, dumping logs.
>> >> Backtrace:
>> >> \           4 (primitive-load "/gnu/store/nh1m265kg7ddar7jgwd7dh8f8y7���")
>> >> In ice-9/eval.scm:
>> >>    191:35  3 (_ _)
>> >> In srfi/srfi-1.scm:
>> >>     640:9  2 (for-each #<procedure b84680 at /gnu/store/f95ghy8mx00���> 
>> >> ���)
>> >> In 
>> >> /gnu/store/f95ghy8mx00fc22nrvswvnpqlfdkf2nk-module-import/guix/build/gnu-build-system.scm:
>> >>    799:31  1 (_ _)
>> >>     369:6  0 (check #:target _ #:make-flags _ #:tests? _ # _ # _ # _)
>> >>
>> >> /gnu/store/f95ghy8mx00fc22nrvswvnpqlfdkf2nk-module-import/guix/build/gnu-build-system.scm:369:6:
>> >>  In procedure check:
>> >> Throw to key `srfi-34' with args `(#<condition &invoke-error [program: 
>> >> "make" arguments: ("test" "-j" "2") exit-status: 2 term-signal: #f 
>> >> stop-signal: #f] b8a840>)'.
>> >> builder for 
>> >> `/gnu/store/qpvqn6ff2lmfq74ff3i9pz5hrb01p9hw-python2-2.7.14.drv' failed 
>> >> with exit code 1
>> >> @ build-failed 
>> >> /gnu/store/qpvqn6ff2lmfq74ff3i9pz5hrb01p9hw-python2-2.7.14.drv - 1 
>> >> builder for 
>> >> `/gnu/store/qpvqn6ff2lmfq74ff3i9pz5hrb01p9hw-python2-2.7.14.drv' failed 
>> >> with exit code 1
>> >
>> > It was trying to build python2, and tests failed.
>> > Could you retry this to see if it is a persistent failure, or the
>> > tests are failing indeterministically?
>> 
>> Specifically, could you try running:
>> 
>>   guix build /gnu/store/qpvqn6ff2lmfq74ff3i9pz5hrb01p9hw-python2-2.7.14.drv
>> 
>> ?
>> 
>> If you enabled substitutes (pre-built binaries) you should now be
>> getting substitutes for this.
>> 
>> If that is the case, you can go ahead and rerun ‘guix pull’.
>> 
>> (This doesn’t tell us why you were getting test failures in the first
>> place, but that’s a separate issue.)
>> 
>> HTH,
>> Ludo’.
>> 
>> 
>>