[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [PATCH 0/6] Enable Cubieboard A10 boot SPL from SD card
From: |
Strahinja Jankovic |
Subject: |
Re: [PATCH 0/6] Enable Cubieboard A10 boot SPL from SD card |
Date: |
Thu, 8 Dec 2022 20:24:40 +0100 |
Hi Niek,
On Wed, Dec 7, 2022 at 9:25 PM Niek Linnenbank <nieklinnenbank@gmail.com> wrote:
>
> Hello Strahinja,
>
> Thanks for contribution these patches, and also taking the H3 into account :-)
Thank you for looking into these patches and all of the comments. I
will try to submit V2 of this patch set in the following days.
>
> I've ran the avocado based acceptance tests for both boards and got these
> results:
>
> $ ARMBIAN_ARTIFACTS_CACHED=yes AVOCADO_ALLOW_LARGE_STORAGE=yes
> ./build/tests/venv/bin/avocado --show=app,console run -t machine:orangepi-pc
> tests/avocado/boot_linux_console.py
> ...
> RESULTS : PASS 5 | ERROR 0 | FAIL 0 | SKIP 0 | WARN 0 | INTERRUPT 0 |
> CANCEL 0
> JOB TIME : 114.24 s
>
> $ ./build/tests/venv/bin/avocado --show=app,console run -t machine:cubieboard
> tests/avocado/boot_linux_console.py
> ...
> RESULTS : PASS 2 | ERROR 0 | FAIL 0 | SKIP 0 | WARN 0 | INTERRUPT 0 |
> CANCEL 0
> JOB TIME : 22.79 s
I did not think initially about avocado, but maybe I could also add an
SPL/SD boot test for the cubieboard, similarly to the way it is run
for Orange Pi, for V2 of the patch set?
Best regards,
Strahinja
>
> So that shows both machines are still running fine. During startup of the
> bionic 20.08 image for orangepi-pc it did show this message:
> console: i2c i2c-0: mv64xxx: I2C bus locked, block: 1, time_left: 0
> console: sy8106a: probe of 0-0065 failed with error -110
>
> The SY8106a appears to be an peripheral attached to the I2C bus on the
> orangepi-pc, and we don't emulate the SY8106a yet, so that's an error to be
> expected:
> https://linux-sunxi.org/SY8106A
>
> So for the series:
> Tested-by: Niek Linnenbank <nieklinnenbank@gmail.com>
>
> I'll try to reply to each patch as well.
>
> Kind regards,
> Niek
>
> On Sun, Dec 4, 2022 at 12:19 AM Strahinja Jankovic
> <strahinjapjankovic@gmail.com> wrote:
>>
>> This patch series adds missing Allwinner A10 modules needed for
>> successful SPL boot:
>> - Clock controller module
>> - DRAM controller
>> - I2C0 controller (added also for Allwinner H3 since it is the same)
>> - AXP-209 connected to I2C0 bus
>>
>> It also updates Allwinner A10 emulation so SPL is copied from attached
>> SD card if `-kernel` parameter is not passed when starting QEMU
>> (approach adapted from Allwinner H3 implementation).
>>
>> Boot from SD card has been tested with Cubieboard Armbian SD card image and
>> custom
>> Yocto image built for Cubieboard.
>> Example usage for Armbian image:
>> qemu-system-arm -M cubieboard -nographic -sd
>> ~/Armbian_22.11.0-trunk_Cubieboard_kinetic_edge_6.0.7.img
>>
>>
>> Strahinja Jankovic (6):
>> hw/misc: Allwinner-A10 Clock Controller Module Emulation
>> hw/misc: Allwinner A10 DRAM Controller Emulation
>> hw/i2c: Allwinner TWI/I2C Emulation
>> hw/misc: Allwinner AXP-209 Emulation
>> hw/arm: Add AXP-209 to Cubieboard
>> hw/arm: Allwinner A10 enable SPL load from MMC
>>
>> hw/arm/Kconfig | 5 +
>> hw/arm/allwinner-a10.c | 40 +++
>> hw/arm/allwinner-h3.c | 11 +-
>> hw/arm/cubieboard.c | 11 +
>> hw/i2c/Kconfig | 4 +
>> hw/i2c/allwinner-i2c.c | 417 ++++++++++++++++++++++++++
>> hw/i2c/meson.build | 1 +
>> hw/misc/Kconfig | 10 +
>> hw/misc/allwinner-a10-ccm.c | 224 ++++++++++++++
>> hw/misc/allwinner-a10-dramc.c | 179 +++++++++++
>> hw/misc/allwinner-axp-209.c | 263 ++++++++++++++++
>> hw/misc/meson.build | 3 +
>> include/hw/arm/allwinner-a10.h | 27 ++
>> include/hw/arm/allwinner-h3.h | 3 +
>> include/hw/i2c/allwinner-i2c.h | 112 +++++++
>> include/hw/misc/allwinner-a10-ccm.h | 67 +++++
>> include/hw/misc/allwinner-a10-dramc.h | 68 +++++
>> 17 files changed, 1444 insertions(+), 1 deletion(-)
>> create mode 100644 hw/i2c/allwinner-i2c.c
>> create mode 100644 hw/misc/allwinner-a10-ccm.c
>> create mode 100644 hw/misc/allwinner-a10-dramc.c
>> create mode 100644 hw/misc/allwinner-axp-209.c
>> create mode 100644 include/hw/i2c/allwinner-i2c.h
>> create mode 100644 include/hw/misc/allwinner-a10-ccm.h
>> create mode 100644 include/hw/misc/allwinner-a10-dramc.h
>>
>> --
>> 2.30.2
>>
>
>
> --
> Niek Linnenbank
>
- [PATCH 4/6] hw/misc: Allwinner AXP-209 Emulation, (continued)
- [PATCH 4/6] hw/misc: Allwinner AXP-209 Emulation, Strahinja Jankovic, 2022/12/03
- [PATCH 2/6] hw/misc: Allwinner A10 DRAM Controller Emulation, Strahinja Jankovic, 2022/12/03
- [PATCH 3/6] hw/i2c: Allwinner TWI/I2C Emulation, Strahinja Jankovic, 2022/12/03
- [PATCH 5/6] hw/arm: Add AXP-209 to Cubieboard, Strahinja Jankovic, 2022/12/03
- Re: [PATCH 0/6] Enable Cubieboard A10 boot SPL from SD card, Niek Linnenbank, 2022/12/07
- Re: [PATCH 0/6] Enable Cubieboard A10 boot SPL from SD card,
Strahinja Jankovic <=