Re: [Discuss-gnuradio] PyBombs installation issue

Hi Martin,

Yeah. Please find below the output

$ ls ~/rfnoc/bin

gnuradio-config-info
uhd_cal_tx_iq_balance
usrp2_card_burner
octoclock_firmware_burner
uhd_config_info
usrp_n2xx_simple_net_burner
rfnocmodtool
uhd_find_devices
usrp_x3xx_fpga_burner
thrift
uhd_image_loader
volk-config-info
uhd_cal_rx_iq_balance
uhd_images_downloader
volk_modtool
uhd_cal_tx_dc_offset
uhd_usrp_probe
volk_profile

$ pybombs inv

PyBOMBS - INFO - PyBOMBS Version 2.3.1a
Showing package state:
uhd-fpga:           installed
uhd:                installed
apache-thrift:      installed
gnuradio:           installed
gr-ettus:           installed

You get anything from this? Thanks

Usman

On Thu, Jan 19, 2017 at 5:15 AM, Martin Braun <address@hidden> wrote:

It's almost as if UHD installed, but GNU Radio didn't, although your
output says otherwise.

What does

$ ls ~/rfnoc/bin

look like?

Or

$ pybombs inv

?

On 01/18/2017 02:10 AM, Usman Haider wrote:
> Hi Nicolas,
>
> Thanks for your time. I did that but the result is same. I can run
>
> |$|uhd_images_downloader
> but
> |$ gnuradio-companion
> |
>
> fails. Let me know if any further information is needed. Thanks
>
> --
> Usman
> On Wed, Jan 18, 2017 at 2:11 PM, Nicolas Cuervo
> <address@hidden <mailto:address@hiddencom>> wrote:
>
> Hello Usman,
>
> Did you set up your PyBOMBS environment? If not, please do so. As
> long as I understand your prefix is at ~/rfnoc. Being that the case,
> please run:
>
> $ source ~/rfnoc/setup_env.sh
>
> After this your shell will have access to everything which has been
> installed in that prefix, and you should be able to start
> gnuradio-companion. Please have in mind that you have to set up this
> environment in every new shell you start.
>
> Please let us know if this doesn't work so that we can look further
> into it.
>
> Cheers,
>
> - Nicolas
>
> On Wed, Jan 18, 2017 at 9:58 AM, Usman Haider

> <address@hidden <mailto:address@hiddencom>> wrote:
>
> Yes, could be the cause. After running the following commands
>
> $ cd ~/rfnoc
> $ source ./setup_env.sh
> $ uhd_images_downloader
>
> I was able to download the images. But when I tried to run
>
> |$ gnuradio-companion|
>
> It failed giving "The program 'gnuradio-companion' is currently
> not installed. You can install it by typing: sudo apt-get
> install gnuradio". Although, I have
>
> $ gnuradio-config-info --v
> v3.7.10.1-202-g6225e5d4
>
> $ gnuradio-config-info --prefix
> /home/emb/rfnoc
>
> Otuput of PyBOMBS is as under.
>
> $ pybombs prefix init ~/rfnoc -R rfnoc -a rfnoc
> PyBOMBS - INFO - PyBOMBS Version 2.3.1a
> PyBOMBS.prefix - INFO - Creating directory `/home/emb/rfnoc'
> Alias `rfnoc' already exists, overwrite Y/[N]? y
> PyBOMBS.ConfigManager - INFO - Creating new config file
> /home/emb/rfnoc/.pybombs/config.yml
> PyBOMBS.prefix - INFO - Installing default packages for prefix...
> PyBOMBS.prefix - INFO -
> - gnuradio
> - uhd
> - gr-ettus
> - uhd-fpga
> PyBOMBS.install_manager - INFO - Phase 1: Creating install tree
> and installing binary packages:
> DEPRECATION: The default format will switch to columns in the
> future. You can use --format=(legacy|columns) (or define a
> format=(legacy|columns) in your pip.conf under the [list]
> section) to disable this warning.
> Install tree:
> |
> +- uhd-fpga
> |
> \- gr-ettus
> |
> +- uhd
> |
> \- gnuradio
> |
> +- uhd
> |
> \- apache-thrift
> PyBOMBS.install_manager - INFO - Phase 2: Recursively installing
> source packages to prefix:
> PyBOMBS.install_manager - INFO - Installing package: apache-thrift
> Cloning: (100%)
> [=========================================================]]
> Cloning: (100%)
> [=========================================================]
> Configuring: (100%)
> [=========================================================]
> Building: (100%)
> [=========================================================]
> Installing: (100%)
> [=========================================================]
> PyBOMBS.install_manager - INFO - Installation successful.
> PyBOMBS.install_manager - INFO - Installing package: uhd
> Cloning: (100%)
> [=========================================================]]
> Configuring: (100%)
> [=========================================================]
> Building: (100%)
> [=========================================================]
> Installing: (100%)
> [=========================================================]
> PyBOMBS.install_manager - INFO - Installation successful.
> PyBOMBS.install_manager - INFO - Installing package: gnuradio
> Cloning: (100%)
> [=========================================================]]
> Configuring: (100%)
> [=========================================================]
> Building: (100%)
> [=========================================================]
> Installing: (100%)
> [=========================================================]
> PyBOMBS.install_manager - INFO - Installation successful.
> PyBOMBS.install_manager - INFO - Installing package: gr-ettus
> Cloning: (100%)
> [=========================================================]
> Configuring: (100%)
> [=========================================================]
> Building: (100%)
> [=========================================================]
> Installing: (100%)
> [=========================================================]
> PyBOMBS.install_manager - INFO - Installation successful.
> PyBOMBS.install_manager - INFO - Installing package: uhd-fpga
> Cloning: (100%)
> [=========================================================]]
> Configuring: (100%)
> [=========================================================]
> Building: (100%)
> [=========================================================]
> Installing: (100%)
> [=========================================================]
> PyBOMBS.install_manager - INFO - Installation successful.
>
>
> Any pointers? :)
>
> --
> Usman
>
>
> On Tue, Jan 17, 2017 at 4:47 PM, Marcus Müller

> <address@hidden <mailto:address@hiddencom>> wrote:
>
> Possibly just a temporary failure then; github or your
> network might have had problems :)
>
> Cheers,
>
> Marcus
>
>
> On 17.01.2017 08:01, Usman Haider wrote:
>> Hello Marcus,
>>
>> I am surprised the following command ran successfully.
>>
>> $ pybombs -vv recipes add gr-recipes
>> git+https://github.com/gnuradio/gr-recipes.git
>> <https://github.com/gnuradio/gr-recipes.git>
>>
>> --
>> Usman
>>
>> On Mon, Jan 16, 2017 at 5:10 PM, Marcus Müller
>> <address@hidden
>> <mailto:address@hiddencom>> wrote:
>>
>> Hm, interesting. Could you run your pybombs command
>> with "-vv"?
>>
>> Best regards,
>>
>> Marcus
>>
>> On 01/16/2017 12:55 PM, Usman Haider wrote:
>>> Hello Nicolas,
>>>
>>> Thanks for your reply. I have sufficient disk space,
>>> more than 400 GB, so that is not an issue. I do not
>>> have any .gitconfig file in my home directory. I can
>>> download the recipes manually using the command you
>>> mentioned.
>>>
>>> git clone https://github.com/gnuradio/gr-recipes.git
>>> <https://github.com/gnuradio/gr-recipes.git> gr-recipes
>>>
>>>
>>> Please let me know if you need any further
>>> information. Thanks.
>>>
>>> --
>>> Usman
>>>
>>> On Mon, Jan 16, 2017 at 3:21 PM, Nicolas Cuervo
>>> <address@hidden

>>> <mailto:address@hiddencom>> wrote:
>>>
>>> Hello Usman,
>>>
>>> uhm, this is odd. So far I can see the command is
>>> correct. Although error 128 means that git did
>>> not exit cleanly, and I just run it and it ran
>>> fine. Just some guesses for now:
>>>
>>> 1. Do you have enough disk space? the recipes do
>>> not require a lot of disk space, though, but not
>>> enough space would lead to this.
>>> 2. Do you have specific cloning configuration in
>>> your gitconfig? you can check this by typing:
>>> git config --global --edit
>>>
>>> or just by editing .gitconfig which is normally
>>> located at your home directory.
>>> 3. Can you clone anything else manually? you can
>>> try running:
>>>
>>> git clone
>>> https://github.com/gnuradio/gr-recipes.git
>>> <https://github.com/gnuradio/gr-recipes.git>
>>> gr-recipes
>>>
>>> just as a test that your git is working as
>>> expected.
>>>
>>> Please let us know if you find out something with
>>> this hypothesis I mentioned.
>>>
>>> Cheers,
>>>
>>> - Nicolas
>>>
>>>
>>>
>>>
>>> On Mon, Jan 16, 2017 at 9:46 AM, Usman Haider
>>> <address@hidden

>>> <mailto:address@hiddencom>> wrote:
>>>
>>> I am following this guide to get started with
>>> RFNoC. I am using Ubuntu 14.04 and I ran
>>> following commands
>>>
>>> $ sudo apt-get install git
>>> $ sudo apt-get install python-setuptools python-dev build-essential
>>> $ sudo easy_install pip
>>> $ sudo pip install git+https://github.com/gnuradio/pybombs.git
>>> <https://github.com/gnuradio/pybombs.git>
>>>
>>> When I run following command
>>>
>>> $ pybombs -v recipes add gr-recipes git+https://github.com/gnuradio/gr-recipes.git
>>> <https://github.com/gnuradio/gr-recipes.git>
>>>
>>> I get output.
>>> ..... ..... ..... OMBS.PackageManager - DEBUG
>>> - Checking if package git is installed...
>>> PyBOMBS.Packager.apt - DEBUG - Package git
>>> has version 1.9.1 installed
>>> PyBOMBS.install_manager - DEBUG - Phase 2:
>>> Recursively installing source packages to
>>> prefix: PyBOMBS.Fetcher.git - DEBUG -
>>> Requirements met. PyBOMBS.Fetcher.git - DEBUG
>>> - Using url -
>>> https://github.com/gnuradio/gr-recipes.git
>>> <https://github.com/gnuradio/gr-recipes.git>
>>> PyBOMBS._process_thread() - DEBUG - Executing
>>> command `git clone
>>> https://github.com/gnuradio/gr-recipes.git
>>> <https://github.com/gnuradio/gr-recipes.git>
>>> gr-recipes' Cloning: [
>>> PyBOMBS.recipes - ERROR - Could not fetch
>>> recipesCloning: [ PyBOMBS.recipes - ERROR
>>> - Could not fetch recipes: Process
>>> returnCloning: (100%)
>>> [=========================================================]
>>> PyBOMBS.monitor_process() - DEBUG - Thread
>>> signaled termination or returned
>>> PyBOMBS.monitor_process() - DEBUG - Return
>>> value: 128 PyBOMBS.recipes - ERROR - Could
>>> not fetch recipes: Process returned value: 128
>>> What could be the issue? pybombs version is
>>> 2.3.1a. Thanks --
>>> Usman
>>> _______________________________________________
>>> Discuss-gnuradio mailing list
>>> address@hidden

>>> <mailto:address@hiddenorg>
>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>> <https://lists.gnu.org/mailman/listinfo/discuss-gnuradio>
>>>
>>>
>>> _______________________________________________
>>> Discuss-gnuradio mailing list
>>> address@hidden
>>> <mailto:address@hiddenorg>
>>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>>> <https://lists.gnu.org/mailman/listinfo/discuss-gnuradio>
>> _______________________________________________
>> Discuss-gnuradio mailing list address@hidden
>> <mailto:address@hiddenorg>
>> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio <https://lists.gnu.org/mailman/listinfo/discuss-gnuradio>
>>
>>
>
>
> _______________________________________________
> Discuss-gnuradio mailing list
> address@hidden <mailto:address@hiddenorg>
> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio

> <https://lists.gnu.org/mailman/listinfo/discuss-gnuradio>
>
>
>
>
>
> _______________________________________________
> Discuss-gnuradio mailing list
> address@hidden
> https://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>

_______________________________________________
Discuss-gnuradio mailing list
address@hidden
https://lists.gnu.org/mailman/listinfo/discuss-gnuradio

From:	Usman Haider
Subject:	Re: [Discuss-gnuradio] PyBombs installation issue
Date:	Thu, 19 Jan 2017 11:35:16 +0500